APM 2.5 5Pin için 20cm APM 2.5 5Pin Konnektör Kablosu İncelemeleri - Banggood Türkiye Çevrimiçi Alışveriş

:

Download the

Banggood App

Uygulamayı indirin ve edinin

ABD$3 indirim kuponu

Teslimat:

Dil:

Para birimi:

Merhabalar Oturum Aç Katıl
Oturum Aç Bize katıl
Yenimisiniz? Başlangıç
0

APM 2.5 5Pin için 20cm APM 2.5 5Pin Konnektör Kablosu

US$6.99
~~US$8.99~~
Şimdi satın al

Müşteri Değerlendirmesi

4.92 üzerinden

36 incelemelerin tümünü görüntüle

Bir Değerlendirme Yaz Yayınlanan ilk 3 incelemeden biri senin incelemen olsun.2 kat Banggood puanı kazan!

Toplam (36) İnceleme
(3) Görüntü
(0) Video
Tüm Yıldızlar
- Tüm Yıldızlar(36)
- 5 Yıldız(33)
- 4 Yıldız(3)
- 3 Yıldız(0)
- 2 Yıldız(0)
- 1 Yıldız(0)

Göre sırala:

En İyi İnceleme

En İyi İnceleme
En Yararlı
En Son

Yalnızca ülkenizden yorumlar (Turkey)

|

Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

qcshopperVIP1
US
02/05/2016

I used this to connect a minimOSD to my CX-20 (with APM 2.5.2), with two small modifications: 1) On the connector use a hobby knife to shave the two protrusions that prevent the connector from fitting into the FC's UART port. (These would be along the edge that will be closest to the circuit board.) 2) Reverse the order of the wires so that the colors are correct for this APM. Ground is on the side closest to the USB port. The one next to GND can be removed. +5V is at the end opposite GND.

I used this to connect a minimOSD to my CX-20 (with APM 2.5.2), with two small modifications: 1) On the connector use a hobby knife to shave the two protrusions that prevent the connector from fitting into the FC's UART port. (These would be along the edge that will be closest to the circuit board.) 2) Reverse the order of the wires so that the colors are correct for this APM. Ground is on the side closest to the USB port. The one next to GND can be removed. +5V is at the end opposite GND.

I used this to connect a minimOSD to my CX-20 (with APM 2.5.2), with two small modifications: 1) On the connector use a hobby knife to shave the two protrusions that prevent the connector from fitting into the FC's UART port. (These would be along the edge that will be closest to the circuit board.) 2) Reverse the order of the wires so that the colors are correct for this APM. Ground is on the side closest to the USB port. The one next to GND can be removed. +5V is at the end opposite GND.
2

Yorumlar

Orjinali göster
juju-anVIP1
MX
14/07/2016

la calidad es aceptable.

la calidad es aceptable.

la calidad es aceptable.
0

Yorumlar

Orjinali göster

Show:

Toplam 0 sayfaları

Sayfaya git

Git

İlginizi çekebilir

recommendation for you