Müşteri Değerlendirmesi

4.92 üzerinden
Bir Değerlendirme Yaz
  • Toplam (90) İnceleme
  • (16) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(90)
    • 5 Yıldız(83)
    • 4 Yıldız(7)
    • 3 Yıldız(0)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
  • April-08 2020 12:14:25

    Got a different pcb than the previous comment that showed the different pads to solder to flash the firmware. I could easily flash the switch with the rx/tx/gpio0 pins accessible at the front and 5V power via the pins already present at the back. Used the same esphome config as a sonoff touch wall switch. Switch works perfectly.

    Yorumlar (1)
  • February-05 2020 05:38:55

    It works as described. You need to put capacitor in parallel with the lamp as described. It works also with my google home mini, so I can control it with voice. :-)

    Yorumlar
  • March-10 2020 02:24:26

    Good product. I could install Tasmota on it. You need to connect to the pads above the chipset. The pinout is from left to right TX, RX, GND, VCC, GPIO0 (see picture attached). When you power on the device you need to connect GPIO0 to GND in order to start the programming mode. I selected "Sonoff Dual R2" in the Tasmota configuration and I see that it works without issues.

    Yorumlar
  • February-22 2020 02:07:08

    Works very good with ESPHome (just took some effort to flash as pins are not marked). Very silent and responsive. Capacitor really small compared to T4 one. Two of them doesn't fit in normal JB setup.

    Yorumlar (1)
  • July-29 2020 06:09:39

    These work really well. Flashable with Tasmota. Just be careful of the pads for the headers, the solder can easily come off when removing the link cables. Best to use a solder pump and very little pressure.

    Yorumlar
  • February-27 2020 08:03:03

    excellent product

    Yorumlar
  • December-20 2019 02:44:08

    This is my second switch. The device has a modern design, good quality and works well.

    Yorumlar (1)
  • October-27 2020 17:32:05

    + bonne sensibilité et la couleur rouge sur le bouton quand la lumière est allumée c’est vraiment bien - la dalle en verre fragile

    Yorumlar
  • September-06 2020 16:35:36

    This is the pinouts on this board if anyone wants to flash with tasmota firmware. These work great and the capacitor is easy enough to fit.

    Yorumlar
  • July-18 2020 14:02:32

    Works just fine. Easy integration with Google Home.

    Yorumlar
Show:

    Go to page

    Go

    İlginizi çekebilir

    recommendation for you
    • TRY71.22
    • TRY47.45
    • TRY71.22
    • TRY87.06
    • TRY94.99
    • TRY47.45
    • TRY356.25
    • TRY39.53
    • TRY152.50
    • TRY183.87
    • TRY95.86
    • TRY73.52
    • TRY124.69
    • TRY94.99
    • TRY99.03
    • TRY63.30
    • TRY110.83
    • TRY88.49