Perfecto, como siempre. Gracias.

Perfecto, como siempre. Gracias.

Perfecto, como siempre. Gracias.

... bis jetzt alles gut ...

... bis jetzt alles gut ...

... bis jetzt alles gut ...

動作の確認はしていません。良い商品に見えます。

動作の確認はしていません。良い商品に見えます。

動作の確認はしていません。良い商品に見えます。

It's a standard Arduino Pro Mini with 5V supply and 16 MHz. It work's really well, the Arduino bootloader was already installed und I could start immediately. It fits nicely into my own project and works flawlessly.

It's a standard Arduino Pro Mini with 5V supply and 16 MHz. It work's really well, the Arduino bootloader was already installed und I could start immediately. It fits nicely into my own project and works flawlessly.

It's a standard Arduino Pro Mini with 5V supply and 16 MHz. It work's really well, the Arduino bootloader was already installed und I could start immediately. It fits nicely into my own project and works flawlessly.

It's not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

It's not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

It's not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

Not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

Not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

Not bad. On one of the three I blinked a LED. The quality is not high. The mask is not gaudy. Contact areas are small and not even. This is not Italy.

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

tested one and works well. was able to flash through UNO. fast shipping too. pic is how I connected to UNO board. Tx to Tx, Rx to Rx, 5v and ground. also need to ground the reset pin on UNO board to disable the boot loader. when flashing wait for the message to change to 'uploading ' and then press the reset button on the pro-mini. if u time it correctly then your program will be uploaded successfully.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

I found a site that showed me how to modify my RC832 Receiver using this Arduino Pro Mini board and the HC-06 Bluetooth module. It allows me to use an App on my phone to change the frequency and auto scan. It took about an hour mostly because the board was setup differently than the one used in the demo and wanted to make sure I had the correct connections. The A6 & A7 pins are in different locations and I was looking for the VCC on the side of the board (there is one on the end of the board) but this says ACC. I was not familiar with ACC but took a chance and it worked. The board was easy to flash and had no issues.

Item as described. Arrived in 2 months (delivery to Italy). Performed just a power test and seemed to be ok.

Item as described. Arrived in 2 months (delivery to Italy). Performed just a power test and seemed to be ok.

Item as described. Arrived in 2 months (delivery to Italy). Performed just a power test and seemed to be ok.

Купил Ардуинок для будущего проекта Chorus Laptimer. Проверил скетчем Blinlk все рабочие, пайку особо не рассматривал, но вроде все ок, да и флюс отмыт. Так что можно брать ;)

Купил Ардуинок для будущего проекта Chorus Laptimer. Проверил скетчем Blinlk все рабочие, пайку особо не рассматривал, но вроде все ок, да и флюс отмыт. Так что можно брать ;)

Купил Ардуинок для будущего проекта Chorus Laptimer. Проверил скетчем Blinlk все рабочие, пайку особо не рассматривал, но вроде все ок, да и флюс отмыт. Так что можно брать ;)