Müşteri Değerlendirmesi

4.88 üzerinden
Bir Değerlendirme Yaz
  • Toplam (207) İnceleme
  • (23) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(207)
    • 5 Yıldız(191)
    • 4 Yıldız(11)
    • 3 Yıldız(3)
    • 2 Yıldız(0)
    • 1 Yıldız(2)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
  • Fabian
    DE
    2019-10-17 08:38:34

    this is NOT the BME280, I got BMP280 with no humidity reported by the sensor. The marking on the chip shows it, too, as I know for now. I trusted the reviews, but obviously they changed the board. You can look it up in the data sheets: BME280: https://www.embeddedadventures.com/datasheets/BME280.pdf (chapter 7.7) BMP280: https://cdn-shop.adafruit.com/datasheets/BST-BMP280-DS001-11.pdf (chapter 7.3) The BME280 with humidity measurement has one dot and one vent hole, the BMP280 only has one dot -

    Yorumlar
  • ubervav
    NO
    2020-02-22 11:10:40

    Good product. Reads temperature, humidity, pressure and altitude. Tested the values with internet, and the values are a bit off, but all in all accurate enough. Note that this is a BME280 clone with SPI bus and won't work with I2C. Used some extra days on shipping, but I'm still overall pleased with my purchase.

    Yorumlar
  • 2020-04-18 08:19:37

    Globalement bon produit, bonne fabrication, mais qualité moyenne, emballage antistatique

    Yorumlar
  • Lugito
    PE
    2019-11-10 09:40:02

    Good quality product

    Yorumlar
  • 2019-11-07 15:26:33

    Ok

    Yorumlar
  • 2020-01-31 05:21:29

    Always a fantastic product

    Yorumlar
  • sebdu38
    FR
    2019-10-08 07:40:44

    Fonctionne parfaitement. Pas de problèmes. Génial pour des projets DIY.

    Yorumlar
  • 2020-09-09 10:51:52

    Fast delivery, proper packaging, testing in progress. Thanks

    Yorumlar
  • 2019-05-05 03:18:24

    the model received is not exactly of the image, but it's a true BME280 and works perfectly. the breadboard contains a pull-up resistors, necessary for I2C and SPI protocols. I have worked directly on arduino, but for security, you use a level-shifter for adapt the logic levels (5v-to-3.3v). pd. I see multiple comments that say that module is not a BME280, is a BMP280. The marks on the module can induce an error, but the chip is a REAL BME280 and reads good the temperature, pressure and humidity

    Yorumlar (1)
  • 2018-02-23 14:56:34

    I just hooked this up to an ESP8266 NodeMCU board using the Arduino IDE and firmware and it works great with the Adafruit BME280 library. Like others have said, I just had to change the I2C address to 0x76. The temp and humidity values seem comparable to the readings I was getting from the DHT22 sensor that I replaced with this because I also wanted barometric pressure readings. Wish these would be a bit cheaper but I only need one of them, the rest of my boards will be fine with DHT22s for temperature

    Yorumlar
Show:

    Go to page

    Go

    İlginizi çekebilir

    recommendation for you
    • TRY30.93
    • TRY87.14
    • TRY46.44
    • TRY77.45
    • TRY54.19
    • TRY38.69
    • TRY46.44
    • TRY54.19
    • TRY30.93
    • TRY123.96
    • TRY10.00
    • TRY15.43
    • TRY15.43
    • TRY15.43
    • TRY23.18
    • TRY56.90
    • TRY23.18
    • TRY93.73