Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (101) İnceleme
  • (8) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(101)
    • 5 Yıldız(77)
    • 4 Yıldız(11)
    • 3 Yıldız(7)
    • 2 Yıldız(2)
    • 1 Yıldız(4)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 16/05/2021

    Put the unit together and all seems to fit apart from Id say the belt it maybe 1 or 2 teeth short as when I run my gantry up to the very top the stress on the rods is too much for the motor and it skips steps, but if Im only going up to 190mm high its working great, maybe over time the belt will loosen off a bit. It was also missing t-buts for the upper middle belt tensioner (which is not really needed as the belt it probably too tight rather than being loose enough to need a tensioner). lead screws are nice and straight and the bracket to fit onto the RHS of the X gantry fits great. I did have to design and 3D print a piece to fit under the RHS rod bearing holder to stop the RH lead screw - I added a photo of it (printed in white with an M3 nut and bolt.

    Yorumlar (3)
    Orjinali göster
  • 13/03/2021

    Einwandfrei. Teile passen sehr gut an meinen Ender 3. Der Zahnriemen ist ein bisschen kurz. Man benötigt den Riemenspanner nicht.

    Yorumlar (2)
    Orjinali göster
  • 22/07/2020

    It does not come with instructions but any skilled DIYer could manage it. Check some YouTube videos if necessary. All the items required are there. The belt need to be put in place before installing the geared pulley, because the belt is not very stretchable. Make sure that the 2nd Z screw is aligned as much as possible to the frame and loosen up the T8 nut which will help with the screw wobble. Do not forget to put some grease on the screws.

    Yorumlar
    Orjinali göster
  • 28/09/2021

    le barre filettate sono arrivate dritte, nonostante l'imballaggio non fosse dei migliori. i pezzi non erano stati imbottiti. mancano le istruzioni cartacee. su internet si trovano dei video di come si monta anche se delle istruzioni stampate avrebbero fatto comodo. la stampante con questa modifica non ha più il problema di sincronismo con il doppio asse Z. Consiglio l'acquisto.

    Yorumlar (2)
    Orjinali göster
  • 26/01/2022

    Ich habe leider kein zusammengebautes Foto gemacht, aber es funktioniert wunderbar! Leider ist mein Ender 3 selten im Einsatz, da ich mir einen neuen Drucker gekauft habe, aber falls ich mehr drucken muss, habe ich schon beide gleichzeitig laufen lassen. Ich bin zufrieden, gute Qualität, top!

    Yorumlar
    Orjinali göster
  • 27/11/2021

    Great product. Mine is fine but sticks came without any box. Luckily they didn't bend on the shipping.

    Yorumlar
    Orjinali göster
  • 21/09/2021

    Everything is alright.

    Yorumlar
    Orjinali göster
  • 07/05/2021

    Kam recht flott an und funktioniert perfekt!

    Yorumlar
    Orjinali göster
  • 22/04/2021

    nagyon jó, köszönöm 🌟🌟

    Yorumlar
    Orjinali göster
  • 12/02/2021

    Gutes Update für meinen Ender 3V2. Der Einbau ist einfach und schnell gemacht. Ich habe zusätzlich noch zwei Axialkugellager eingebaut damit die zweite Gewindespindel nicht in der Lagerung rutschen kann.

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • US$14.75
    • US$8.99
    • US$9.99
    • US$19.99
    • US$4.99
    • US$34.99
    • US$5.99
    • US$299.00
    • US$399.00
    • US$3.99
    • US$8.99
    • US$22.99
    • US$29.99
    • US$60.99