Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (5412) İnceleme
  • (606) Görüntü
  • (7) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(5412)
    • 5 Yıldız(5258)
    • 4 Yıldız(121)
    • 3 Yıldız(18)
    • 2 Yıldız(4)
    • 1 Yıldız(11)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 14/04/2016

    Using this on an Eachine 250 Racer with Flysky-i6 transmitter. Range and reliability is extremely good. Price is unbeatable. Two-way data link allows monitoring of Racer battery voltage and low battery alert (using the RC groups mod to monitor external voltage instead of RX voltage - that is the yellow wire emerging from a small notch made in the casing at the joint line in the attached photo). I have tried a Flysky CVT01 voltage measurement module which works well but the Flysky-i6 transmitter does not allow me to set a low voltage alert for the measurement returned by the CVT01 - so the RC groups mod is better in this respect.

    Yorumlar (8)
    Orjinali göster
  • 21/07/2015

    Works GREAT! with my new FS-i6. Great to have the expanded range and two way communication. Thanks Bangood And FlySky!

    Yorumlar (3)
    Orjinali göster
  • 17/09/2020

    os produtos chegaram perfeito só os correios daqui que demoram mais tive todo apoio da bangood .sempre me orientou com o pedido . e não foi o primeiro e nem o último vou comprar mais obrigado bangood.

    Yorumlar
    Orjinali göster
  • 29/07/2016

    It's green! You gotta love this quad (packaging, components, price)! I can't imagine a better first-time FPV racing quad. The F3 color scheme really comes alive in low light conditions because the individual ESC's, PDB, and rear LED strip all glow green. Mine came ready-to-fly. I didn’t need to put this ‘on the bench’ to bind the transmitter or setup the ESC’s, flight controller, etc. Here’s the steps I took: Step 1: Install the antenna on the VTx port on the top plate. This is very important because the Video Transmitter (VTx) would otherwise overheat and fail within minutes of plugging the battery into the quad. Step 2: Ensure the props are NOT installed. Again, this is an important precaution when first introducing the transmitter to the quad's receiver. Step 3: Feed the battery strap through the long slits on the top-plate. Strap down the battery but DO NOT apply power to the quad. Step 4: Turn on the transmitter and place all switches up, and spin the rotary dials fully CCW to their stops (10 o'clock position). Also retard the throttle to idle/cutoff (fully aft). Step 5: Power the quad and wait for beep sequence from the flight controller. You should see a steady red light on the VTx just under the quad's top plate. And NO red light on the flight controller. If the VTx red light is blinking then you may need to bind the Tx with the Rx (reference YouTube "FS-i6 binding"). If the flight controller is flashing red, then repeat Steps 4 & 5 until you hear the flight controller sing. Once the red light on the flight controller extinguishes, flip the SWB (long switch at upper left side of the FS-i6 Tx) down to '2'. The red light on the flight controller should re-appear to indicate 'armed' (and dangerous). Now (without the props installed) you can goose the throttle to check for proper Tx/Rx binding and control. Step 6: Open both bags of props and take out a pair of each. CW=silver nuts; CCW=black nuts. That is '5x4P' (with CCW arrow) on the right-front and left-rear motors, and the '5x4R' (with CW arrow) on the left-front and right-rear. Tighten down the prop nuts Step 7: Open the Instruction Manual to page 4 and note the 3-position SWC switch functions. 1=Auto (self-leveling like toy-quads and camera drones); 2= Mixed (horizon mode combining self-leveling with flips at full stick deflection; not useful in windy conditions); 3=Manual (acro mode with no self-leveling; best learned with a simulator or XK X100 or other light-weight acro quad). In other words, first-time FPV racer pilots should ensure SWC is in position '1' for the first flight of this Kingkong 210GT racer! Step 8: Go fly! Enjoy!!!! (or first test and setup FPV as available) Step 8: Disarm the quad using SWB in position '1'. Unplug the battery on the quad, then turn off the transmitter.

    Yorumlar
    Orjinali göster
  • 15/08/2020

    great receiver, easily over 1km range with standard hand set. and over 8 channels using ibus. for better weight and size remove the plastic case and cut off the pins, solder instead

    Yorumlar (1)
    Orjinali göster
  • 21/10/2015

    Heb deze gekocht voor combinatie met turnigy tgy-i10 zender en werkt even goed enige verschil is de veel lagere prijs en dat zonder dure verzendingskosten. Gewoon wat langer hoeven te wachten op levering.

    Yorumlar
    Orjinali göster
  • 05/06/2020

    My favourite afhds 2a receiver, best for 5" quads upwards or wings. Take the receiver out the casing and snip the pins off to malt it more compact and lighter. Have had over 3.5km with this. Can't fault it

    Yorumlar
    Orjinali göster
  • 01/08/2019

    I used it .it's very use full for flying quad .

    Yorumlar
    Orjinali göster
  • 12/01/2017

    Great product, high quality and works fine in PPM - iBus connection with FlySky FS-i6.

    Yorumlar
    Orjinali göster
  • 22/06/2023

    Excelente produto conforme o descrito no anúncio tudo 🆗 funcionando perfeitamente testando e aprovado.

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • US$4.99
    • US$9.99
    • US$19.99
    • US$23.36
    • US$65.99
    • US$29.51
    • US$135.03
    • US$38.99
    • US$39.35
    • US$39.35
    • US$109.99
    • US$244.77
    • US$25.99
    • US$33.99
    • US$20.90
    • US$15.99
    • US$61.49
    • US$5.99