Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (562) İnceleme
  • (68) Görüntü
  • (1) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(562)
    • 5 Yıldız(543)
    • 4 Yıldız(17)
    • 3 Yıldız(2)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 16/11/2020

    It arrived very quickly, in just 11 days, in completely correct physical condition. It remains to be tried. This is a resent item, the previous one was stuck somewhere.

    Yorumlar
    Orjinali göster
  • 13/07/2021

    muito bom

    Yorumlar
    Orjinali göster
  • 13/02/2021

    Good looking little board, I haven't tested it yet but I'm not worried. Came in a sealed ESD safe bag.

    Yorumlar
    Orjinali göster
  • 26/01/2021

    Very good, I use the controler with a joystick sketch and build it in my Saitek yoke to eliminate the annoying deadzone in this yoke.

    Yorumlar
    Orjinali göster
  • 08/10/2020

    Everytking is ok, save package. My old gaming steringwheel saved :)

    Yorumlar
    Orjinali göster
  • 10/06/2021

    Works perfectly! Pins soldered in easily and the code uploaded and worked immediately.

    Yorumlar
    Orjinali göster
  • 28/01/2021

    Good delivery, the item is good, but I haven't used it yet because it has arrived now

    Yorumlar
    Orjinali göster
  • 29/10/2020

    Seems ok.

    Yorumlar
    Orjinali göster
  • 19/09/2020

    muito bom

    Yorumlar
    Orjinali göster
  • 05/05/2019

    I ordered two of these boards and they arrived much faster than I expected and were in good condition. They were individually packed in static bags and came with two header pins as shown on the product page. Soldering them was easy - stick the pins into a breadboard and set the board down so the pins go through the holes. No need for any tools to hold everything in place. Windows 10 recognized the boards and installed the correct drivers automatically; the Arduino application saw them too and I was able to program them immediately. It worked! Note that while this board is compatible with a Leonardo (same MCU), the built-in LED on a Leonardo (on Pin 13) does not exist on this board. I ran into some trouble with one of them that was entirely my own fault. Based on the silkscreen markings on the board and its size, I thought I'd try using the SparkFun Pro Micro drivers. Things worked fine until I programmed the board, after which Windows would no longer recognize it as a usable USB device. Turns out the SparkFun Pro Micro comes in two flavours: 5V/16MHz and 3.3V/8MHz, and the driver defaults to 3.3V/8MHz. The solution to the problem is to change the board type in the Arduino application back to Leonardo (5V), then ground the /RST pin twice, quickly. After that, the bootloader will wait for eight seconds for you to set the Arduino software to the correct COM port and upload your program, making sure you have the board type set to Leonardo. It took me a couple of tries but I brought the board back from the dead. If you ever program your board and it no longer works and your computer can't seem to communicate with it anymore, try the above technique, or do a search for "pro-micro fail troubleshooting" it's where I got the above from. This is a great little board with more pins than you'd expect for a device this small, and it plugs nicely into a breadboard, leaving plenty of room for other components.

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • TRY145.74
    • TRY65.88
    • TRY51.38
    • TRY291.57
    • TRY59.96
    • TRY111.43
    • TRY214.37
    • TRY197.21
    • TRY85.70
    • TRY377.35
    • TRY248.68
    • TRY111.43
    • TRY154.32
    • TRY120.01
    • TRY540.34
    • TRY128.59
    • TRY943.51
    • TRY102.85