Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (37) İnceleme
  • (2) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(37)
    • 5 Yıldız(34)
    • 4 Yıldız(2)
    • 3 Yıldız(1)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 05/02/2022

    tried this out to move my flag. possible to use as camera linear motion stand

    Yorumlar
    Orjinali göster
  • 19/06/2019

    a good produc

    Yorumlar
    Orjinali göster
  • 13/01/2022

    Good product, came well packed in good time, only thing not provided is limit switch and motor leads.

    Yorumlar
    Orjinali göster
  • 02/06/2022

    Ok

    Yorumlar
    Orjinali göster
  • 16/05/2022

    fast shipping, very well packed and secured, excellent shape, thank you :)

    Yorumlar
    Orjinali göster
  • 11/01/2022

    Óptimo produto e serviço

    Yorumlar
    Orjinali göster
  • 21/03/2022

    ベルト式のものを購入したらなぜかボールネジ式のものが届きました。全く違うものが届いたけれどちゃんと動作するのでまあ星3で。

    Yorumlar (1)
    Orjinali göster
  • 23/11/2019

    Note: This is for 400 cm option Sturdy build. Quality parts, and smooth operation. The overall length is about 22 inches, and the travel is about 18 inches. The stepper is standard NEMA 17 with 1.8 deg step with a total revolution of the stepper shaft at 200 steps. For the quality you get, this is a steal of a deal. I highly recommend if you are building budget CNC machine, 3D printer, and engraving machine.

    Yorumlar (1)
    Orjinali göster
  • 16/02/2021

    I have 3 of these Linear Guide sets now for an X/Y pen plotter that may evolve into some sort of CNC tool. I had two problems with the guides, but they were easily fixed. One of the white 3D-printed blocks that holds the idler wheel cracked badly. I machined a replacement out of aluminum and all works good. The other was that all the V-roller wheels ran rough and stuck in some locations. I thought they were bad bearings, but then discovered that the nut and the small brass washer on either side of the bearing/wheel were rubbing on the rotating part when all was tightened down. I added a small cone-shaped lock washer on both sides of the bearing, and now only the stationary inner portion of the bearing is gripped, and the wheel rolls smoothly. The small roller platform moves much smoother and easier now. The motors have worked with no problems. I use the Hanpose TB6600 drivers. This has been a good learning project.

    Yorumlar
    Orjinali göster
  • 21/12/2020

    these are excellent rails , however they need some fine tuning to get them silky smooth. straight out the box they either super tight or completely sloppy. making a 4axis cnc wire cutter with them

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • US$8.99
    • US$13.99
    • US$66.99
    • US$5.99
    • US$33.56
    • US$27.99
    • US$7.99
    • US$69.99
    • US$13.99
    • US$5.99
    • US$5.99
    • US$7.99
    • US$53.37
    • US$9.99
    • US$85.99
    • US$6.63
    • US$59.99
    • US$159.99