Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (1142) İnceleme
  • (62) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(1142)
    • 5 Yıldız(1083)
    • 4 Yıldız(51)
    • 3 Yıldız(4)
    • 2 Yıldız(1)
    • 1 Yıldız(3)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 27/05/2020

    To start, the product fits and secures snugly in my 0xa tool post. The dovetails are well machined and polished, they even took extra time to chamfer the 90° edges and corners that could be uncomfortable when holding it & tightening a tool piece into the holder. ( Nice Job ) I tossed in a comparison piece and covered the brand name because its not important. You will notice the much more expensive 250-001 tool holder (blue tape) did not take the time to chamfer edges and inside the Dado where your tooling will rest the back is not polished and left ruff. They did however also paint/anodize the inside of the Dado. Personally I like the polished metal over more anodizing it does leave more surface exposed and possible damage can take place if you don't take care of the bare surfaces. That part will be a personal preference. Now for a couple small dislikes. The depth from front to back on the more expensive tool holder is 19.98mm the new units are 19.22 it is small but was noticeable without even measuring. I am not sure if the 0.76mm will effect the over all rigidness, or maybe lead to bending dovetails later down the road. I really hope not and would reach out to the manufacturer if an issue came up. The second issue is with the Bottom shelf of the Dado. My original Tool holder has a shelf thickness of 4mm. and the new units have a shelf thickness of 3.82. yes it is small 0.18mm. and this being one of the thinner portions of the tool holder I really wood have liked to see that at full thickness 4mm. Time will tell as I am a chronic over tightener, if the shelf will bend as I tighten the tooling secure screws, or if vibration or chatter over time will weak it to a failing point. The cost was great they arrived early, slightly under packaged for any type of impact damage that could take place in my opinion but they were well oiled and protected from moisture threats.

    Yorumlar
    Orjinali göster
  • 11/12/2020

    This is a quality toolpost and one I am very please with so far. The tools are of a quality construction and the post holds things rock-steady. It does not fit the Myford ML10's stud by default as this is slightly larger than the M10 but a new stud can be purchased from a UK store online, but the base needs to ne turned down in depth by about 1.4mm as it's designed for the ML7. The holders are great quality and while I felt the adjustment screw was fiddly it does the job. my only regret now is not buying more holders 😂 Top job Machifit and I hope you produce a sine bar now, maybe a more extensive range of gauge blocks too!

    Yorumlar (3)
    Orjinali göster
  • 21/03/2021

    Good!

    Yorumlar (1)
    Orjinali göster
  • 01/12/2020

    I must admit, I am pleasantly surprised at how good the quality is on this tool post, it's definitely gibs style and not piston, it's solid and the movent is almost buttery smooth! I now regret not buying the tool holders at the same time and want to install it on my lathe IMMEDIATELY!, but have no tool holder that will work with it! I need to use it NOW! :-D Definitely great value for the money. gonna buy the entire set, a few times 😇

    Yorumlar
    Orjinali göster
  • 25/09/2020

    all items purchased are of excellent quality at a truly competitive price. I am really happy with the purchase. Shipping and receiving in record time. Congratulations to the seller. Thank you

    Yorumlar
    Orjinali göster
  • 26/02/2020

    Ok

    Yorumlar
    Orjinali göster
  • 26/10/2019

    Not packed enough.

    Yorumlar
    Orjinali göster
  • 12/01/2021

    Pienamente soddisfatto!Oggetto come da descrizione, indispensabile per montare utensili 10x10 sul mio piccolo Myford ML7.

    Yorumlar
    Orjinali göster
  • 06/08/2020

    Suitable for my C1 lathe, nicely ground finish on mating faces, no sharp edges or burs.

    Yorumlar
    Orjinali göster
  • 20/05/2020

    Super uchwyt do tokarki hobbystycznej. Działa super, wykonany precyzyjnie, nie zacina się. Oprawki noży tokarskich łatwo się reguluje. Zamontowałem na mojej małej tokarce (klon Sieg C6) po niewielkiej modyfikacji suportu. Polecam.

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • US$49.99
    • US$9.44
    • US$30.57
    • US$158.66
    • US$24.99
    • US$52.85
    • US$23.99
    • US$76.25
    • US$14.75
    • US$105.99
    • US$10.99
    • US$7.91
    • US$11.94
    • US$110.99
    • US$9.28
    • US$20.99
    • US$24.76
    • US$119.99