Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (115) İnceleme
  • (21) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(115)
    • 5 Yıldız(112)
    • 4 Yıldız(2)
    • 3 Yıldız(0)
    • 2 Yıldız(0)
    • 1 Yıldız(1)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 03/11/2020

    Produit pas encore testé. Attention la prise pour la batterie n'est ni soudée ni livrée et les prise servos sont du type JST 1.00mm. On peut remarquer que les composant de de surfaces soudés sur la plaque ne correspondent pas aux photos du site Internet. Je crois que c'est une version mise à jour et que le récepteur supporte les protocoles "AFHDS" et "AFHDS 2A" (voir les commentaires et questions).

    Yorumlar
    Orjinali göster
  • 28/02/2018

    It is a really small and light receiver. The connectors are JST 1.0mm. It has been easily bound with my Flysky FS-i6 transmitter. Some instructions about the connections would be welcomed.

    Yorumlar (5)
    Orjinali göster
  • 12/03/2020

    Super kleiner Empfänger mit integriertem Regler für Bürstenmotoren.Sehr gut für kleine Hallenflieger geeignet.Einzig die 1mm JST Sockel sind nicht für 1S Servos mit hauptsächlich1,25mm JST Steckern geeignet,aber es gibt Adapterkabel.Funktioniert perfekt!

    Yorumlar (2)
    Orjinali göster
  • 14/09/2017

    This receiver is nice and very small but comes without documentation. It is very similar to the "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" Product ID: 1072251 and the "Mini Futaba SFHSS Compatible 8CH Receiver PPM Output With 1mm JST Socket For DIY Micro Quadcopter" Product ID: 1083120 and you can get some more information by digging into the descriptions of these receivers. It binds with my Turnigy 9X / Flysky TH9X but the process takes some time for the first bind to occur. In PPM mode (with a jumper added on the pcb…) the pulses stream is on the signal output of channel 1 / throttle connector. The others channels are not available on the connectors but the ESC output is still usable. See the picture of the waveforms: upper signal is from channel 1 connector, with the ESC output just below. The receptor does not feature cutoff for lipo protection: I tested that the ESC keeps driving a small motor with an input voltage as low as 2.4v. So be careful if you use a 1S lipo. 1.0mm 3-pin JST connectors are not available at Banggood, nor some tiny compatible servos. Just a pity... It is bit expensive if you compare it to a V911 of F929/939 receiver with 2 integrated servos

    Yorumlar (2)
    Orjinali göster
  • 25/11/2018

    This receiver is excellent, I know others have had binding problems with them, I think the software has changed, I use my FS-i6 and AFHDS2A and it binds perfectly, along with telemetry

    Yorumlar (1)
    Orjinali göster
  • 25/09/2018

    Perfect for the small balsa rc models sold here on Banggood. I have used in LX17, Fokker EIII so far. Flying radio range is great. I am still in control when I can barely see plane in distance.

    Yorumlar
    Orjinali göster
  • 08/09/2019

    Small receiver. Easy binding with fs-i6s. Connectors seems like micro and not compatible with 1.7g servo offered by banggood.

    Yorumlar (2)
    Orjinali göster
  • 18/07/2017

    Some instructions would be helpful, the channels are not labeled, the connector for the lipo should be included and the labeling for the motor and battery are poorly labeled. The receiver starts in bind mode on my Ultimate 7E I select flysky and press bind and it binds. Ultimate 7E is Devo 7E with upgraded arm for more memory. I also heave installed a 3in1 multi module which was cheaper on aliexpress.

    Yorumlar
    Orjinali göster
  • 01/08/2017

    it's tiny ! - the same size board as "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" and shares the same 1mm spaced pins in the servo sockets (compatible with hk-5320s servos), although the chip components are laid out differently size and weight consistent with descriptions way smaller than the wltoys f-series receiver (shown for comparison in the pic) the layout would presumably the same as the dsmx version for the wires - motor connections for the esc marked M on the left of the underside, and battery to the right; both with their positive lead on the middle (pair of) solder pads haven't tried it yet, but the dsmx version worked fine, and i expect this should too

    Yorumlar
    Orjinali göster
  • 28/07/2020

    super small Will let you know when i have tried it out

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • US$6.80
    • US$10.55
    • US$25.99
    • US$14.99
    • US$27.10
    • US$7.99
    • US$13.50
    • US$12.29
    • US$61.49
    • US$21.99
    • US$23.99
    • US$11.45
    • US$17.99
    • US$15.99
    • US$18.99
    • US$8.99
    • US$54.99
    • US$31.10