Torontofred Themeter you're using is either an average AC meter or True RMS. In either, the wave form must be sine wave. If you have any other, then you won't be reading it correctly.
Cevap 24/12/2020BG401544916 @Torontofred Canyou explain about what you are talking. About AC or DC current. Thank you.
Cevap 25/12/2020Gerard Vaughan The output is said to be d.c. Ate you saying the makers used an instantaneous peak reading ammeter ? But in any case we don't know if the current is time varying at 100-120 cps. It might be smooth.
Cevap 25/12/2020
Gerard Vaughan
Torontofred
So you reckon the thing supplies full wave rect unsmoothed dc, and the makers are quoting the instantaneous peak current ?
That's still a ssttreeeech !
Pot202 Happy Birthday and Merry Christmas. I would like you to help me fix the machine at 250 amps. With some photo maybe. Thank you very much.
Cevap 26/12/2020Garabonczias Dear All! Some important points: (1) The current should be DC (in AC the arc would disappear 100 times in a second...!). (2) That DC current is never smooth during welding, as contact is bad, arc has haunting (continously changing) resistance
Cevap 02/01/2021
Garabonczias
Torontofred
One more thing: the clamp meter should be TRMS one, with high Crest Factor. Than it will show a better value. BUT, the current waveform is so distorted, you cannot expect a really good meaured value.
Best regards
Mieciu HiMarek - could you explain how to adjust display to show real current values?
Cevap 08/01/2021maz77 hi marek jestes z polski ?
Cevap 09/01/2021luckis @Torontofred Just connect in parallel another electrolytic capacitor 680μf 400v .
Cevap 13/01/2021BG144943792 onde que regulam a maquina pra lamentar a Amperes
Cevap 18/01/2021Kamber Gülmez ben annamadım yazdı MH dan
Cevap 22/01/2021
zappymax
where do you install such described as ====Reply to Torontofred: Just connect in parallel another electrolytic capacitor 680μf 400v .
— if so easy to get 250 amp, why is such additional cap not installed by manufacturer 🤔🤔
Zavah exelente tu aporte muchacho muy bueno :)
Cevap 17/02/2021
Peter
Couldyou post a picture what is included or do i need to buy some tools to start
thx for the review
ushmucan СПАСИБО, МАРЕК. САМЫЙ СОДЕРЖАТЕЛЬНЫЙ ОБЗОР. мой ящик ushmucan yandex ru
Cevap 25/03/2021BG121417372 Where can I get a User Manual please.
Cevap 31/03/2021abo omar abo omar 🔴 Does it work for the quiet and the beginners ??
Cevap 09/04/2021Romanko77 Are welding cables supplied with this device?
Cevap 15/04/2021hitman247 Scesc, I have bought this welder, but unfortunately turned the vr1 potentiometer on main board upside, can you please tell me the original value so I can set it back? unfortunately my welder does not have the trimmer for calibrating display, only fixed resistor or maybe entire small PCB from under display is missing, not visible good enough. thank you
Cevap 03/11/2021REXX5000 the output on welders is AC. not DC. especially these type of welders.
Cevap 22/06/2022REXX5000 @hitman247 remove the fixed resistor and replace with a potentiometer. that's the hack. then measure the output with clampmeter and adjust the the current output on the welders display. enjoy.
Cevap 22/06/2022
بندر الحاتم
مرحبا
مروحة تبريد
كم فولت
Şirketimiz | Bizimle iletişime geçin | Ödeme & Nakliye | Partnerlik Programlarımız |
---|---|---|---|