boa qualidade

boa qualidade

boa qualidade

小さい！ ハンダパット仕様なのでスペースがタイトなときはいいですね(^-^) 基本は他を使いますが 好みのレシーバーが在庫切れだったので602系を何個か買って試してみました 何個かはバインドできずゴミ箱へ バインドできた物はパーツボックスで待機してもらいます(^-^)

小さい！ ハンダパット仕様なのでスペースがタイトなときはいいですね(^-^) 基本は他を使いますが 好みのレシーバーが在庫切れだったので602系を何個か買って試してみました 何個かはバインドできずゴミ箱へ バインドできた物はパーツボックスで待機してもらいます(^-^)

小さい！ ハンダパット仕様なのでスペースがタイトなときはいいですね(^-^) 基本は他を使いますが 好みのレシーバーが在庫切れだったので602系を何個か買って試してみました 何個かはバインドできずゴミ箱へ バインドできた物はパーツボックスで待機してもらいます(^-^)

3 points I noted regarding this receiver: 1. CAUTION, CLUB FLYERS BEWARE: All XJT D16 models on my Taranis X-Lite connect to it, even though they are currently bound to other receivers!!! 2. The telemetry sensor for the Betaflight lua script is not present, so it does not work. 3. The RSSI value with MY transmitter near to it is 107db. My other receivers all read around 100db. Other than that, F.Port set at the higher baud rate works well with the cli settings req'd for most F4's.

3 points I noted regarding this receiver: 1. CAUTION, CLUB FLYERS BEWARE: All XJT D16 models on my Taranis X-Lite connect to it, even though they are currently bound to other receivers!!! 2. The telemetry sensor for the Betaflight lua script is not present, so it does not work. 3. The RSSI value with MY transmitter near to it is 107db. My other receivers all read around 100db. Other than that, F.Port set at the higher baud rate works well with the cli settings req'd for most F4's.

3 points I noted regarding this receiver: 1. CAUTION, CLUB FLYERS BEWARE: All XJT D16 models on my Taranis X-Lite connect to it, even though they are currently bound to other receivers!!! 2. The telemetry sensor for the Betaflight lua script is not present, so it does not work. 3. The RSSI value with MY transmitter near to it is 107db. My other receivers all read around 100db. Other than that, F.Port set at the higher baud rate works well with the cli settings req'd for most F4's.

Was finally able to get this to work through FPort with my F4 Zeus AIO. Yay, no more separate wire for SBUS and telemetry! Can't comment on the range due to the whole covid-19 situation but tests in my underground parking lot seem promising. Also the version I got had the latest 2.02 firmware already on it.

Was finally able to get this to work through FPort with my F4 Zeus AIO. Yay, no more separate wire for SBUS and telemetry! Can't comment on the range due to the whole covid-19 situation but tests in my underground parking lot seem promising. Also the version I got had the latest 2.02 firmware already on it.

Was finally able to get this to work through FPort with my F4 Zeus AIO. Yay, no more separate wire for SBUS and telemetry! Can't comment on the range due to the whole covid-19 situation but tests in my underground parking lot seem promising. Also the version I got had the latest 2.02 firmware already on it.

Item finally delivered (took almost 2 months), condition looks good, did not tested yet. Small as RXSR. Antenna wires quite short, but has ufl connector so can be replaced if needed.

Item finally delivered (took almost 2 months), condition looks good, did not tested yet. Small as RXSR. Antenna wires quite short, but has ufl connector so can be replaced if needed.

Item finally delivered (took almost 2 months), condition looks good, did not tested yet. Small as RXSR. Antenna wires quite short, but has ufl connector so can be replaced if needed.

Smaller than XM+ but has telemetry unlike XM+. A bit more tedious to flash - you need a USB TTL tool and also the Crossover (a.k.a. Oversky) tool (program) from their website. My receiver came with the latest available firmware (v2.02) but I reflashed it anyway. Binding was much easier than Frsky receivers as you don't have to hold down the bind button while plugging in the battery. The other benefit big benefit of this receiver is that the FPort is not inverted (unlike Frsky R-XSR), so you can just connect to a normal TX pad on the flight controller. This is especially useful for those with F4 boards that don't have inverted TX pads. Note that the manual refers to NOR and REV. NOR means normal (not inverted) and REV means reversed (inverted). Finally, the signal does not drop off when the receiver is very close to the transmitter (unlike Frsky receivers like XM+ and R-XSR). That means you won't get failsafe if the craft is near you. Great for flying LOS close by or setting up the craft next to your transmitter on the bench.

Smaller than XM+ but has telemetry unlike XM+. A bit more tedious to flash - you need a USB TTL tool and also the Crossover (a.k.a. Oversky) tool (program) from their website. My receiver came with the latest available firmware (v2.02) but I reflashed it anyway. Binding was much easier than Frsky receivers as you don't have to hold down the bind button while plugging in the battery. The other benefit big benefit of this receiver is that the FPort is not inverted (unlike Frsky R-XSR), so you can just connect to a normal TX pad on the flight controller. This is especially useful for those with F4 boards that don't have inverted TX pads. Note that the manual refers to NOR and REV. NOR means normal (not inverted) and REV means reversed (inverted). Finally, the signal does not drop off when the receiver is very close to the transmitter (unlike Frsky receivers like XM+ and R-XSR). That means you won't get failsafe if the craft is near you. Great for flying LOS close by or setting up the craft next to your transmitter on the bench.

Smaller than XM+ but has telemetry unlike XM+. A bit more tedious to flash - you need a USB TTL tool and also the Crossover (a.k.a. Oversky) tool (program) from their website. My receiver came with the latest available firmware (v2.02) but I reflashed it anyway. Binding was much easier than Frsky receivers as you don't have to hold down the bind button while plugging in the battery. The other benefit big benefit of this receiver is that the FPort is not inverted (unlike Frsky R-XSR), so you can just connect to a normal TX pad on the flight controller. This is especially useful for those with F4 boards that don't have inverted TX pads. Note that the manual refers to NOR and REV. NOR means normal (not inverted) and REV means reversed (inverted). Finally, the signal does not drop off when the receiver is very close to the transmitter (unlike Frsky receivers like XM+ and R-XSR). That means you won't get failsafe if the craft is near you. Great for flying LOS close by or setting up the craft next to your transmitter on the bench.

Polecam szybko przyszło

Polecam szybko przyszło

Polecam szybko przyszło

A good alternative to a Frsky R-XSR, especially if you plan to use FPort No need to flash firmware to use Fport, plus supports Uninverted TX via the main pin, unlike the R-XSR which requires you to solder to the tiny uninverted pad in the middle of the back of the board. Also does not have a plug like the R-XSR, which if trying to save space is a bonus Another nice feature is that Bind Mode does not require you to hold the button while powering up About the only downside seems to be that it requires you to use AETR1234 channel mapping in BF, but still works fine with my Transmitter set to TAER1234

A good alternative to a Frsky R-XSR, especially if you plan to use FPort No need to flash firmware to use Fport, plus supports Uninverted TX via the main pin, unlike the R-XSR which requires you to solder to the tiny uninverted pad in the middle of the back of the board. Also does not have a plug like the R-XSR, which if trying to save space is a bonus Another nice feature is that Bind Mode does not require you to hold the button while powering up About the only downside seems to be that it requires you to use AETR1234 channel mapping in BF, but still works fine with my Transmitter set to TAER1234

A good alternative to a Frsky R-XSR, especially if you plan to use FPort No need to flash firmware to use Fport, plus supports Uninverted TX via the main pin, unlike the R-XSR which requires you to solder to the tiny uninverted pad in the middle of the back of the board. Also does not have a plug like the R-XSR, which if trying to save space is a bonus Another nice feature is that Bind Mode does not require you to hold the button while powering up About the only downside seems to be that it requires you to use AETR1234 channel mapping in BF, but still works fine with my Transmitter set to TAER1234

bardzo dobry odbiornik, wykonany wzorowo, bardzo lekki, anteny mogły by być dłuższe na szczęście można je łatwo wymienić, zasięg jest okej odleciałem na około 900 metrów na terenie w którym mogą występować zakłócenia więc jest bardzo dobrze. szkoda że w zestawie nie ma okablowania.

bardzo dobry odbiornik, wykonany wzorowo, bardzo lekki, anteny mogły by być dłuższe na szczęście można je łatwo wymienić, zasięg jest okej odleciałem na około 900 metrów na terenie w którym mogą występować zakłócenia więc jest bardzo dobrze. szkoda że w zestawie nie ma okablowania.

bardzo dobry odbiornik, wykonany wzorowo, bardzo lekki, anteny mogły by być dłuższe na szczęście można je łatwo wymienić, zasięg jest okej odleciałem na około 900 metrów na terenie w którym mogą występować zakłócenia więc jest bardzo dobrze. szkoda że w zestawie nie ma okablowania.

Solid 16 channel receiver with easy uninverted fport pin for 1-wire control and telemetry. range appears decent. This is the first third-party d16 Rx which impressed me, normally fly all models on xm+. Telemetry on 1 wire with the non-inverted fport is simply awesome. I will be buying more.

Solid 16 channel receiver with easy uninverted fport pin for 1-wire control and telemetry. range appears decent. This is the first third-party d16 Rx which impressed me, normally fly all models on xm+. Telemetry on 1 wire with the non-inverted fport is simply awesome. I will be buying more.

Solid 16 channel receiver with easy uninverted fport pin for 1-wire control and telemetry. range appears decent. This is the first third-party d16 Rx which impressed me, normally fly all models on xm+. Telemetry on 1 wire with the non-inverted fport is simply awesome. I will be buying more.