Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (38) İnceleme
  • (2) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(38)
    • 5 Yıldız(35)
    • 4 Yıldız(1)
    • 3 Yıldız(2)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 21/03/2018

    It is a very nice looking chuck. No rust or mechanical damages. Runout of internal taper socket is about .008". External R8 taper is about .060" too big in diameter, angle may not be correct. The slot is milled off center, but this does not affect the operation. The spanner wrench is OK, no complaints here. I wish they would include a 35 mm wrench for the flats, it is non-standard and a big adjustable wrench is just too wide for that. Overall it is a very good deal for the money, in regards to quality - you need to decide for yourself.

    Yorumlar
    Orjinali göster
  • 29/03/2020

    very good finish. no burrs or chips present. well packed with light oil.

    Yorumlar
    Orjinali göster
  • 03/09/2021

    Fast and good service

    Yorumlar
    Orjinali göster
  • 24/04/2021

    Very good product delivery time excellent thank you very much

    Yorumlar
    Orjinali göster
  • 26/01/2021

    Good quality

    Yorumlar
    Orjinali göster
  • 29/12/2020

    great deal

    Yorumlar
    Orjinali göster
  • 07/12/2020

    buena herramienta

    Yorumlar
    Orjinali göster
  • 01/01/2021

    Although the collet in itself is fine, the thread in the back is on the wonk so the drawbar cannot be screwed in to it. Luckily I have the equipment to machine the thread out, weld in a blank and re-tap the thread. If you don't then you should probably look elsewhere.

    Yorumlar
    Orjinali göster
  • 11/02/2020

    This is the second R8 ER32 collect chuck I have had and both are unusable. On the first one, the inside bore had a run out of .004" and the second one was about the same but on the second one the 7/16 internal thread was not tapped parallel to the shank so the drawbar was very tight and this should be a nice easy fit. I don't normally leave negative feedback but because I have had two and they are both really bad I think it is justified as neither are not fit for purpose.

    Yorumlar (1)
    Orjinali göster
  • 10/03/2018

    Packaged well and appered well made. Checked run out on Bridgeport mill, slightly more run out than my best R8 collets, (this could have been the ER32 collet) but for the price it will serve me well for what i want it to do - as a quick change for drills (which will be more accurate than my keyless chuck)

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • TRY401.33
    • TRY490.53
    • TRY419.17
    • TRY276.44
    • TRY106.96
    • TRY196.16
    • TRY62.35
    • TRY472.69
    • TRY71.27
    • TRY240.76
    • TRY240.76
    • TRY249.68
    • TRY374.57
    • TRY463.77
    • TRY267.52
    • TRY124.80
    • TRY945.47
    • TRY695.70