Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (290) İnceleme
  • (36) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(290)
    • 5 Yıldız(274)
    • 4 Yıldız(14)
    • 3 Yıldız(2)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
|
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 30/12/2020

    Excellent product. Even better than described: The tightening tool has a security spring preventing the tool to be left on the chuck. I had done that on my previous 3/4 jaws to prevent accidents. The quality is very good, it gives an overall impression of serious construction and the run-out is ok for such a small machine accessory. Note that the Alen screws cannot be used on Chinese mini lathe, you need to prepare 6 mm x 30 studs as shown.

    Yorumlar (1)
    Orjinali göster
  • 13/07/2021

    San Ou K72-80.80mm OD body metric independent 4-jaw chuck(not a 3" chuck (3" = 76.2mm).Mounted on Boxford lathe.Well finished tool compliant to its recommended purpose( holding of non-ferrous metals and softer materials eg: aluminium,plastic,wood etc.) Clamps ferrous metal work pieces adequately,however,risk of slippage of the workpiece being turned may result in shearing damage on the jaw holding faces.Do so at your own discretion.Note that the 80mm chuck (K72-80) has a 3 point /3 screw mounting pattern as shown in the photographs.A separate chuck adapter may have to be purchased or fabricated to suit your particular lathe.Mounting boss/flange is 55mm diameter x 4 mm height,3 screw mounting pattern at 120º from each one another.Recommended item.

    Yorumlar
    Orjinali göster
  • 24/03/2021

    velmi pěkný produkt za dobrou cenu OK

    Yorumlar
    Orjinali göster
  • 24/11/2020

    PRODUTO BOM, CHEGOU ANTES DO PREVISTO EU RECOMENDO... AGORA E SO TESTAR O PRODUTO

    Yorumlar
    Orjinali göster
  • 09/08/2021

    good quality, fast delivery.

    Yorumlar
    Orjinali göster
  • 26/04/2021

    utile

    Yorumlar
    Orjinali göster
  • 30/03/2021

    Good.Fast delivery.

    Yorumlar
    Orjinali göster
  • 29/08/2021

    Lools good, jaws are not loose.

    Yorumlar
    Orjinali göster
  • 29/06/2021

    molto bello e professionale

    Yorumlar
    Orjinali göster
  • 24/02/2020

    The unit arrived well packaged & protected. No rust issues, but I did have to clean a decent amount of oil & a bit more machine fouling than I believe should be acceptable on any type of part being labeled precision. The chuck mounted up to my existing Little Machine Shop adapter plate. The first item i tossed in the chuck was a piece of 6mm Brass Round Bar & with not much effort I was able to have it centered to 0.0005" My only complaint is 2 of the 4 chuck jaws were not completely machined & they stopped short of completely facing off the face of the jaws. Pictures included will show the facing issue which I will turn & Face again on my own. At this point it is a product I would definitely purchase again in the future.

    Yorumlar
    Orjinali göster
Show:

    Toplam 0 sayfaları

    Sayfaya git

    Git

    İlginizi çekebilir

    recommendation for you
    • TRY360.93
    • TRY536.57
    • TRY136.51
    • TRY214.57
    • TRY351.18
    • TRY83.82
    • TRY360.93
    • TRY546.33
    • TRY224.33
    • TRY292.63
    • TRY165.78
    • TRY390.21
    • TRY136.51
    • TRY1,073.24
    • TRY682.94
    • TRY360.93
    • TRY110.75
    • TRY360.93