Müşteri Değerlendirmesi

4.86 üzerinden
Bir Değerlendirme Yaz
  • Toplam (226) İnceleme
  • (23) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(226)
    • 5 Yıldız(207)
    • 4 Yıldız(11)
    • 3 Yıldız(5)
    • 2 Yıldız(1)
    • 1 Yıldız(2)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
  • February-25 2020 08:46:53

    I’ve been unable to make it work when it is directly plugged on my UNO clone. However it works perfectly when I use the Rx, Tx and Gnd pins from the UART under the Status and NetLight LEDs (as shown in picture). For my project it’s okay, but could be a problem if you want the shield to be stacked. In addition it’s clearly not brand new... but hey, at this price point I can’t complain since it’s working!

    Yorumlar
  • September-16 2020 06:26:07

    Arrived on time, in good conditions. SIM card adapters included too (unexpected). Not tested yet.

    Yorumlar
  • December-06 2020 15:11:53

    hızli geldi ama daha kütüphanesi falan hangisidir bakmadım kurmadım dış görünüşü saglam bir sıkıntı yok

    Yorumlar
  • January-25 2021 13:49:39

    Thanks

    Yorumlar
  • March-19 2020 02:56:38

    سريع و جيد في الاتصال

    Yorumlar
  • December-09 2019 07:32:13

    Like on the description, delivery was fast, i am happy about it. I did not yet try it. Just a pity there is not the male pins to plug the shield directly on the arduino

    Yorumlar
  • August-26 2018 05:37:44

    Well it came very fast,like 7-8 working days. (location Greece) The package was in a good condition and the shield itself also. I havent tested it yet but I dont see any damage.

    Yorumlar
  • December-23 2016 07:40:12

    Recibido hoy después de casi 1 mes con envio priority, todavia no lo he probado dado que se necesita una pila CR1220 (En cualquier tienda creo que las encuentras) tiene buena calidad veremos que tal funciona.

    Yorumlar
  • February-09 2017 12:41:42

    the DC-DC converter MIC29302WU on the board has 5 pins and uses about 7mA in standby. I cut all traces to pin 1 and 2 and connected pin 2 to RAW and pin 1 to an unused port. so i can shut down the DC-DC converter completely. HIGH on pin1: MIC29302WU working LOW on pin1: MIC29302WU shut down, no current use! best wishes from austria

    Yorumlar
  • December-06 2015 14:20:00

    Works perfect. Writing a working sketch in arduino is a little bit more difficult because libraries found online doesn't work with this module. You must make your own library or sketch from beginning.

    Yorumlar (1)
Show:

    Total 0 pages

    Go to page

    Go

    İlginizi çekebilir

    recommendation for you
    • TRY47.48
    • TRY28.54
    • TRY60.32
    • TRY82.96
    • TRY96.93
    • TRY37.67
    • TRY30.12
    • TRY67.87
    • TRY45.22
    • TRY90.51
    • TRY52.77
    • TRY25.52
    • TRY22.57
    • TRY52.77
    • TRY82.96
    • TRY67.87
    • TRY19.25
    • TRY22.57