Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (110) İnceleme
  • (14) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(110)
    • 5 Yıldız(104)
    • 4 Yıldız(3)
    • 3 Yıldız(1)
    • 2 Yıldız(1)
    • 1 Yıldız(1)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 05/02/2021

    Fast shipping! The product arrived in a short time! Careful packaging. Excellent quality. Delivered by GLS. I tried it: it works properly. You can also accept filament rolls of different makes and sizes!

    Orjinali göster
  • 11/08/2021

    Sensacional, é tão silencioso que nem ouço seu funcionamento. O visor e os botões agradam, sendo um para ajuste do timer, e, outro para ajustar a temperatura. Revestimento interno top. Chegou em 11 dias após a postagem!

    Orjinali göster
  • 11/11/2021

    Product well packed, arrived in good order. Took it apart to add the fan modification similar to that described here https://www.youtube.com/watch?v=6FG4O5l9XpE, but using a 3d printed fan shroud like this one: https://www.thingiverse.com/thing:4729474, with a 24 volts, 40x10mm fan. The fan makes a huge difference circulating hot air around the filament spool, keeping the temperature even. The temperature sensor wire was extended as in the video to be moved to a more representative location at the top of the cabinet. Removing the display bezel was probably the trickiest part of the mod. Suggest using an old credit card to push into the gap between the display bezel and the case to remove the bezel, rather than using pliers as in the video. It does require quite a lot of force to push the bezel snap fit clips down enough to be able to pull the bezel free. I am very happy with the performance now. Without the mod it is still a good product.

    Orjinali göster
  • 15/04/2021

    Good filament dryer, I use it mainly for TPU and PETG filament which are more hydrophilic than e.g. PLA. Display shows current temperature and two buttons allow to control temperature and drying duration. The default time is 6h and the preset 50°C seems to be good for most filaments. Haven't used it during prints yet, to dry (potentially) wet filament using it before the print seems to be sufficient as I always seal filaments in a plastic bag with desiccant anyway (had problems with some filament once anyway, that's the reason why I bought a dryer) What I really miss is a button to simply switch it off !! Decreasing the drying time to 0 is a cumbersome workaround !!

    Orjinali göster
  • 05/09/2021

    great product, very easy to use, I would love if the temperature was a little higher because its not very good to dry nylon, but for abs, pla and petg its great

    Orjinali göster
  • 21/10/2021

    Harika bir ürün, herkese tavsiye ederim.

    Orjinali göster
  • 05/10/2021

    Super, rytoj bandysiu

    Orjinali göster
  • 23/07/2021

    very good products and quality. fast shipping

    Orjinali göster
  • tweb

    Works well and is simple to use. Great if your using tpu to get that moisture out👍👌

    Orjinali göster
  • 03/11/2021

    perfetto come da descrizione!funziona molto bene!

    Orjinali göster

    Toplam 0 sayfaları

    Sayfaya git


    İlginizi çekebilir

    recommendation for you
    • TRY4,655.37
    • TRY3,610.00
    • TRY472.65
    • TRY3,052.47
    • TRY97.43
    • TRY641.02
    • TRY87.67
    • TRY710.71
    • TRY4,460.09
    • TRY208.93