Very good. Thank you

Very good. Thank you

Very good. Thank you

Clamps very well to the blade and doesn't move around. On the picture it's on my Tarot 450 wooden blade. It doesn't squeeze too tight to leave any marks. Also tried on my Goblin 630 blades. There's room to spare so it would fit on even bigger blades. The precision of 0.1 degrees is nice and quite accurate. It's more than you need. Make sure you use it on a levelled surface! You can verify it with the same gauge. NB! You will need two CR2032 batteries!

Clamps very well to the blade and doesn't move around. On the picture it's on my Tarot 450 wooden blade. It doesn't squeeze too tight to leave any marks. Also tried on my Goblin 630 blades. There's room to spare so it would fit on even bigger blades. The precision of 0.1 degrees is nice and quite accurate. It's more than you need. Make sure you use it on a levelled surface! You can verify it with the same gauge. NB! You will need two CR2032 batteries!

Clamps very well to the blade and doesn't move around. On the picture it's on my Tarot 450 wooden blade. It doesn't squeeze too tight to leave any marks. Also tried on my Goblin 630 blades. There's room to spare so it would fit on even bigger blades. The precision of 0.1 degrees is nice and quite accurate. It's more than you need. Make sure you use it on a levelled surface! You can verify it with the same gauge. NB! You will need two CR2032 batteries!

Firstly like a lot of other people mine was faulty on arrival would switch it on and screen would come on but immediately switch off. I knew it would take ages to get tech support from banggood and returning the item and then if they decided to send me a new one, i estimated this was going to take towards 3 months so really was not worth the effort and cost. I looked on youtube and found a coupe of videos which show how to fix the main problem with these. It is the solder joints on the press buttons of the circuit board, which means removing 10 screws to remove the circuit board, then i crocodile cliped it to my piece holder which hasa magnifying glass on it, and carefully resoldered the joints and put it all back together. refitted the battery and tested it. Now it is all working, but again this is a banggood quality control issue they need to test the items before shipping. Note also that this does not come with any cr2032 batteries which you require 2 of them for. It also does not have a auto swith off so i remove batteries when in storage or not using. But once you have a working pich gauge it does a good job and is fairly accurate sufficient for measuring pitch of your blades o your helicoipter and setting them up correctly (lots of you tube videos on this , some better than others so view a few first to get a good idea).

Firstly like a lot of other people mine was faulty on arrival would switch it on and screen would come on but immediately switch off. I knew it would take ages to get tech support from banggood and returning the item and then if they decided to send me a new one, i estimated this was going to take towards 3 months so really was not worth the effort and cost. I looked on youtube and found a coupe of videos which show how to fix the main problem with these. It is the solder joints on the press buttons of the circuit board, which means removing 10 screws to remove the circuit board, then i crocodile cliped it to my piece holder which hasa magnifying glass on it, and carefully resoldered the joints and put it all back together. refitted the battery and tested it. Now it is all working, but again this is a banggood quality control issue they need to test the items before shipping. Note also that this does not come with any cr2032 batteries which you require 2 of them for. It also does not have a auto swith off so i remove batteries when in storage or not using. But once you have a working pich gauge it does a good job and is fairly accurate sufficient for measuring pitch of your blades o your helicoipter and setting them up correctly (lots of you tube videos on this , some better than others so view a few first to get a good idea).

Firstly like a lot of other people mine was faulty on arrival would switch it on and screen would come on but immediately switch off. I knew it would take ages to get tech support from banggood and returning the item and then if they decided to send me a new one, i estimated this was going to take towards 3 months so really was not worth the effort and cost. I looked on youtube and found a coupe of videos which show how to fix the main problem with these. It is the solder joints on the press buttons of the circuit board, which means removing 10 screws to remove the circuit board, then i crocodile cliped it to my piece holder which hasa magnifying glass on it, and carefully resoldered the joints and put it all back together. refitted the battery and tested it. Now it is all working, but again this is a banggood quality control issue they need to test the items before shipping. Note also that this does not come with any cr2032 batteries which you require 2 of them for. It also does not have a auto swith off so i remove batteries when in storage or not using. But once you have a working pich gauge it does a good job and is fairly accurate sufficient for measuring pitch of your blades o your helicoipter and setting them up correctly (lots of you tube videos on this , some better than others so view a few first to get a good idea).

works good

works good

works good

great product

great product

great product

nickel

nickel

nickel

good

good

good

good product!

good product!

good product!

thankyou so much came on time

thankyou so much came on time

thankyou so much came on time

as described, thanks

as described, thanks

as described, thanks