aún no lo uso llego dentro del tiempo estimado, y en un empaque decente

aún no lo uso llego dentro del tiempo estimado, y en un empaque decente

aún no lo uso llego dentro del tiempo estimado, y en un empaque decente

Bought to silence a resin printer, which it did very well. The 2209 with the free 2208 which came with it actually worked out cheaper than buying 2208 (which is the one I only needed) on its own, so it was like buying a cheap 2208 and getting a free, quality 2209, bargain! Very fast delivery, too.

Bought to silence a resin printer, which it did very well. The 2209 with the free 2208 which came with it actually worked out cheaper than buying 2208 (which is the one I only needed) on its own, so it was like buying a cheap 2208 and getting a free, quality 2209, bargain! Very fast delivery, too.

Bought to silence a resin printer, which it did very well. The 2209 with the free 2208 which came with it actually worked out cheaper than buying 2208 (which is the one I only needed) on its own, so it was like buying a cheap 2208 and getting a free, quality 2209, bargain! Very fast delivery, too.

I bought these to upgrade my custom designed 3d printer and as its a corexy with dual z screws, i shall be using four out of the six with two spare.Its easy enough to just replace your A4988 or Drv8825 stepper drivers (adjust the current) to run in legacy mode (stealth chop) but the motor direction will need to be swapped in your firmware and for UART mode extra wires are to be added to communicate with firmware if not supported on your controller board....Excellent price and fast delivery by Banggood THANKS, 3 days and delivered.

I bought these to upgrade my custom designed 3d printer and as its a corexy with dual z screws, i shall be using four out of the six with two spare.Its easy enough to just replace your A4988 or Drv8825 stepper drivers (adjust the current) to run in legacy mode (stealth chop) but the motor direction will need to be swapped in your firmware and for UART mode extra wires are to be added to communicate with firmware if not supported on your controller board....Excellent price and fast delivery by Banggood THANKS, 3 days and delivered.

I bought these to upgrade my custom designed 3d printer and as its a corexy with dual z screws, i shall be using four out of the six with two spare.Its easy enough to just replace your A4988 or Drv8825 stepper drivers (adjust the current) to run in legacy mode (stealth chop) but the motor direction will need to be swapped in your firmware and for UART mode extra wires are to be added to communicate with firmware if not supported on your controller board....Excellent price and fast delivery by Banggood THANKS, 3 days and delivered.

Everything well packed and protected. Very good quality components. Recommended

Everything well packed and protected. Very good quality components. Recommended

Everything well packed and protected. Very good quality components. Recommended

Working perfectly, with these motor drivers are really lower the noise

Working perfectly, with these motor drivers are really lower the noise

Working perfectly, with these motor drivers are really lower the noise

Installed those on my tevo tornado. Very nice results and the printer runs very quiet now. This upgrade is a MUST !

Installed those on my tevo tornado. Very nice results and the printer runs very quiet now. This upgrade is a MUST !

Installed those on my tevo tornado. Very nice results and the printer runs very quiet now. This upgrade is a MUST !

driver au top. vraiement silencieux. il fonctionne très bien avec une carte RAMPS 1.6

driver au top. vraiement silencieux. il fonctionne très bien avec une carte RAMPS 1.6

driver au top. vraiement silencieux. il fonctionne très bien avec une carte RAMPS 1.6

nice one👍

nice one👍

nice one👍

Just fitted these tmc2208 drivers with a skr 1.3 controller, so far so good. The 2208 drivers really makes the motors silent, only noise I can hear from the printer now is the fans.

Just fitted these tmc2208 drivers with a skr 1.3 controller, so far so good. The 2208 drivers really makes the motors silent, only noise I can hear from the printer now is the fans.

Just fitted these tmc2208 drivers with a skr 1.3 controller, so far so good. The 2208 drivers really makes the motors silent, only noise I can hear from the printer now is the fans.

best update made in my tarantula pro. so accurate and silence the step motors running now.

best update made in my tarantula pro. so accurate and silence the step motors running now.

best update made in my tarantula pro. so accurate and silence the step motors running now.