Haven't tested it yet but it seems good and durable.

Haven't tested it yet but it seems good and durable.

Haven't tested it yet but it seems good and durable.

package was in good condition, didn't test the product yet

package was in good condition, didn't test the product yet

package was in good condition, didn't test the product yet

trienglelab quality asa usual.. thank you.

trienglelab quality asa usual.. thank you.

trienglelab quality asa usual.. thank you.

It a good thermistor and will work with SKR mini e3 2.0 control board as is. Hoewer resolution will be lower compared to other thermistors as SKR mini e3 2.0 control board comes with 4.7K resistor connected on the thermistor pins. To release potential abilities of the PT1000 sensors,you need to replace the 4.7K pullup resistor of the thermistor pins with a 1K 0.1% resister and compile Marlin.

It a good thermistor and will work with SKR mini e3 2.0 control board as is. Hoewer resolution will be lower compared to other thermistors as SKR mini e3 2.0 control board comes with 4.7K resistor connected on the thermistor pins. To release potential abilities of the PT1000 sensors,you need to replace the 4.7K pullup resistor of the thermistor pins with a 1K 0.1% resister and compile Marlin.

It a good thermistor and will work with SKR mini e3 2.0 control board as is. Hoewer resolution will be lower compared to other thermistors as SKR mini e3 2.0 control board comes with 4.7K resistor connected on the thermistor pins. To release potential abilities of the PT1000 sensors,you need to replace the 4.7K pullup resistor of the thermistor pins with a 1K 0.1% resister and compile Marlin.

ok!

ok!

ok!

Produkt rewelacja, dużo dodatków.

Produkt rewelacja, dużo dodatków.

Produkt rewelacja, dużo dodatków.

Everything is OK.

Everything is OK.

Everything is OK.

Great thermistor. If you're buying it for Artillery Sidewinder, keep in mind that you need to change stock heat-block because the cartridge is too long for it. You can get a PT100/PT1000 compatible aluminum volcano heat block from Trianglelabs under 5$ or buy the plated copper version. Copper plated version will cost you more and it's much heavier though. You don't need it if you plan to print with only PLA. PT1000 doesn't need an amplifier board like the PT100, so I suggest you get this one instead. Firmware adjustment is needed.

Great thermistor. If you're buying it for Artillery Sidewinder, keep in mind that you need to change stock heat-block because the cartridge is too long for it. You can get a PT100/PT1000 compatible aluminum volcano heat block from Trianglelabs under 5$ or buy the plated copper version. Copper plated version will cost you more and it's much heavier though. You don't need it if you plan to print with only PLA. PT1000 doesn't need an amplifier board like the PT100, so I suggest you get this one instead. Firmware adjustment is needed.

Great thermistor. If you're buying it for Artillery Sidewinder, keep in mind that you need to change stock heat-block because the cartridge is too long for it. You can get a PT100/PT1000 compatible aluminum volcano heat block from Trianglelabs under 5$ or buy the plated copper version. Copper plated version will cost you more and it's much heavier though. You don't need it if you plan to print with only PLA. PT1000 doesn't need an amplifier board like the PT100, so I suggest you get this one instead. Firmware adjustment is needed.

I received faster than what I'm expecting

I received faster than what I'm expecting

I received faster than what I'm expecting

Pretty good balance between cost and quality. PT1000 is comparable to generic 100k NTC even without modification to board, but the spread between different thermistors is much less than that of 100k NTC and the included 0.1% 1K 0603 resistor to modify the controller board this is on par with PT100 but better signal to noise and no expensive amplifier needed.. Wire not suitable for cable chains so has to be spiced at a toolhead that uses cable chains. This is my go to thermistor and Trianglelabs make a good product ad a descent price.

Pretty good balance between cost and quality. PT1000 is comparable to generic 100k NTC even without modification to board, but the spread between different thermistors is much less than that of 100k NTC and the included 0.1% 1K 0603 resistor to modify the controller board this is on par with PT100 but better signal to noise and no expensive amplifier needed.. Wire not suitable for cable chains so has to be spiced at a toolhead that uses cable chains. This is my go to thermistor and Trianglelabs make a good product ad a descent price.

Pretty good balance between cost and quality. PT1000 is comparable to generic 100k NTC even without modification to board, but the spread between different thermistors is much less than that of 100k NTC and the included 0.1% 1K 0603 resistor to modify the controller board this is on par with PT100 but better signal to noise and no expensive amplifier needed.. Wire not suitable for cable chains so has to be spiced at a toolhead that uses cable chains. This is my go to thermistor and Trianglelabs make a good product ad a descent price.