Müşteri Değerlendirmesi

Bir Değerlendirme Yaz
  • Toplam (10) İnceleme
  • (3) Görüntü
  • (0) Video
  • Tüm Yıldızlar
    • Tüm Yıldızlar(10)
    • 5 Yıldız(10)
    • 4 Yıldız(0)
    • 3 Yıldız(0)
    • 2 Yıldız(0)
    • 1 Yıldız(0)
Göre sırala:
En İyi İnceleme
  • En İyi İnceleme
  • En Yararlı
  • En Son
Yalnızca ülkenizden yorumlar (Turkey)
Orjinali göster

İncelemenin bir kısmı otomatik olarak çevrildi.

  • 02/11/2021

    Haven't tested it yet but it seems good and durable.

    Orjinali göster
  • 23/10/2021

    package was in good condition, didn't test the product yet

    Orjinali göster
  • 03/02/2022

    trienglelab quality asa usual.. thank you.

    Orjinali göster
  • 04/08/2022

    It a good thermistor and will work with SKR mini e3 2.0 control board as is. Hoewer resolution will be lower compared to other thermistors as SKR mini e3 2.0 control board comes with 4.7K resistor connected on the thermistor pins. To release potential abilities of the PT1000 sensors,you need to replace the 4.7K pullup resistor of the thermistor pins with a 1K 0.1% resister and compile Marlin.

    Orjinali göster
  • 02/06/2022


    Orjinali göster
  • 21/04/2022

    Produkt rewelacja, dużo dodatków.

    Orjinali göster
  • 05/04/2022

    Everything is OK.

    Orjinali göster
  • VexVIP3

    Great thermistor. If you're buying it for Artillery Sidewinder, keep in mind that you need to change stock heat-block because the cartridge is too long for it. You can get a PT100/PT1000 compatible aluminum volcano heat block from Trianglelabs under 5$ or buy the plated copper version. Copper plated version will cost you more and it's much heavier though. You don't need it if you plan to print with only PLA. PT1000 doesn't need an amplifier board like the PT100, so I suggest you get this one instead. Firmware adjustment is needed.

    Orjinali göster
  • 04/12/2021

    I received faster than what I'm expecting

    Orjinali göster
  • 23/11/2021

    Pretty good balance between cost and quality. PT1000 is comparable to generic 100k NTC even without modification to board, but the spread between different thermistors is much less than that of 100k NTC and the included 0.1% 1K 0603 resistor to modify the controller board this is on par with PT100 but better signal to noise and no expensive amplifier needed.. Wire not suitable for cable chains so has to be spiced at a toolhead that uses cable chains. This is my go to thermistor and Trianglelabs make a good product ad a descent price.

    Orjinali göster

    Toplam 0 sayfaları

    Sayfaya git

    recommendation for you
    • US$17.99
    • US$59.19
    • US$8.99
    • US$19.99
    • US$5.99
    • US$60.74
    • US$32.39
    • US$39.99
    • US$159.99
    • US$50.99
    • US$56.99
    • US$44.99
    • US$119.99
    • US$69.99
    • US$63.99
    • US$221.99
    • US$32.99
    • US$29.99