En iyi fiyatlar Güneş Paneli,Güneş Paneli,Adım Aşağı Modülü

Adi 02/07/2022

I received it after 5 days from CZ in good conditions. The system is functional with a maximum power of about 7 W (full sun, 17 June 14:00 1st image: Lead Acid Battery charge). At the panel dimension I expected less than 20 W anyway (0.1 sqM x 1000 W X 20% = 20 W). The open circuit voltage is 18.1 V (2nd image) and the short circuit current 0.54 A (3rd image), the temperature is about 50 degree C (4th image). The voltage-current and power-current characteristics were measured (with a constant current load - 5th image), the measurement at 0.5 A is visible in the 6th image. The controller current consumption (from battery or solar panel is of 12 mA). The controller disconnects the battery from panel at about 14.4V and reconnect it at about 13.5V, I did not notice the PWM operation. For small solar panels (like this one) it is a good choice, for higher solar power a MPPT controller would be more efficient. Overall I consider this a good deal (I bought it at about 30 USD); be aware that the solar panel power is less than 10 W.

100W Güneş Paneli seti 12V pil Şarj Cihazı 10-100A LCD Kontrolör Karavan Van Tekne için

US$30.74 US$39.99

56

Yorumlar (13)

Adi 22/09/2022

The board arrives in Romania from CN in about one month. The MPPT regulator with CN3722 is operating well. I recommend it as the cheapest MPPT I have found (about 9 USD); its operation is based on constant input voltage (called MPPT voltage). It can be used as it is, but I preferred to modify its heatsink because it is a risk of electrical contact, the insulation is the heatsink black paint only; I made a 3 mm hole in the ground connection under D1 and put an additional heatsink on the top of PMOS and diodes - connect them with a 3 mm screw (photo 1 and 2) - under the original heatsink I used kapton tape and thermal paste. The schematic of the board can be seen on figure 3 with the pin names taken from the CN3722 datasheet (typical circuit - photo 4). The adjustment can be done directly with the solar panel (SP) - adjust V_MPPT to the point where the LED(s) are blinking without battery connected; in this point you get 1.04V (typical) on MPPT terminal, over R5; you can adjust V_MPPT also based on the SP characteristics, to the maximum power voltage (about 15..20% less than the open-circuit voltage) using an additional source (with the current limited to less than 1A) settled to the desired voltage (adjust to get 1.04V over R5 and/or to the LED blinking point, without battery). With the battery connected you can adjust the end of charge voltage to the point where you get 2.416V (typical) to the FB pin - over R7, OR when the battery reach the end-charge voltage adjust to the point where the LEDs change the color - from blue to red (dimmed) in my case - blue is charging, red is end of charge (in my case - normally one expects red for charging...). I tested the panel with low light on a cloudy day (w/o heatsink) with a 100W 22V solar panel, I get about 20% more power compared with the MPPT of the XMUND XD-PS1 power station. I will test it also on a sunny day (with heatsink now) and I will add a comment.

MPPT 5A Güneş Paneli Regülatör Kontrol Cihazı Pil Şarjı 9V 12V 24V Otomatik Anahtar

US$13.99 US$16.99

6

Yorumlar (2)

Adi 12/08/2019

The unit is OK. I tested it for 24V input, 11V output ay 10A current. The output voltage is relatively constant (from 11.5V no load to 11.2V at 10A). The temperatures are: 100 dgr.C for transformer, 100 dgr.C for one heatsink and 80 dgr.C for the other.

Geekcreit® DC 6-40V İle 1.2-36V 300W 20A Sabit Akım Ayarlanabilir Buck Dönüştürücü Adım Aşağı Modül Kartı

US$12.29 US$9.99

19

Yorumlar (5)

Adi 09/08/2019

I tested the unit and the results are verygood: - open circuit voltage 11.9V - loaded voltage: 11.8V at 5A - maximum output current 6.3A - steady-state temperature: 60dgr.C the case, 110 drg.C the transformer (at 5A after 1 hour).

Geekcreit® AC 100-240V'dan DC 12V 5A 60W Anahtarlama Güç Kaynağı Modülü Sürücü Adaptörü LED Şerit Işığı

US$9.83 US$11.99

39

Yorumlar (0)

Adi 22/06/2022

I received the panel in good condition in 9 days from CZ. It is light (2.2 kg) and flexible. I tested the panel on June 21, at 14:00, full sun. Open circuit voltage is 22.1V, short-circuit current 5.5A; maximum power is about 85W (4.5A, 19V) - the electrical characteristics can be seen in photo. The operation temperature is about 50 degree C (I get a maximum of 54 C). Overall I consider the panel to be good, with realistic parameters (compared with the small ones - declared at much higher power).

100W 18V Esnek Güneş Paneli Pil Güç Şarj Kiti RV Araba Boat Camping için

US$154.99 US$175.99

6

Yorumlar (0)

TOPŞAK TS-ED3 20V 10mm Electric Drill 2 Gear Speed Adjustment Switch Stepless 30N.m Torque W/1pc Battery EU/US Plug and 43pcs Accessories

US$86.09 US$109.99

Q: brushless motor

Soran BG149179423 Açık 2022-11-24 05:32:36

Adi ED3 model is brush motor - there are sparks in the rear part produced by the motor collector.

2022-12-03 10:31:19 Yararlı

Gönder

cevaplar (1)

Adi Inthe schematics there is a small mistake... VCC is connected to S_PMOS point (after M1 - protection to reverse voltage at the panel input).

Adi 22/09/2022

The board arrives in Romania from CN in about one month. The MPPT regulator with CN3722 is operating well. I recommend it as the cheapest MPPT I have found (about 9 USD); its operation is based on constant input voltage (called MPPT voltage). It can be used as it is, but I preferred to modify its heatsink because it is a risk of electrical contact, the insulation is the heatsink black paint only; I made a 3 mm hole in the ground connection under D1 and put an additional heatsink on the top of PMOS and diodes - connect them with a 3 mm screw (photo 1 and 2) - under the original heatsink I used kapton tape and thermal paste. The schematic of the board can be seen on figure 3 with the pin names taken from the CN3722 datasheet (typical circuit - photo 4). The adjustment can be done directly with the solar panel (SP) - adjust V_MPPT to the point where the LED(s) are blinking without battery connected; in this point you get 1.04V (typical) on MPPT terminal, over R5; you can adjust V_MPPT also based on the SP characteristics, to the maximum power voltage (about 15..20% less than the open-circuit voltage) using an additional source (with the current limited to less than 1A) settled to the desired voltage (adjust to get 1.04V over R5 and/or to the LED blinking point, without battery). With the battery connected you can adjust the end of charge voltage to the point where you get 2.416V (typical) to the FB pin - over R7, OR when the battery reach the end-charge voltage adjust to the point where the LEDs change the color - from blue to red (dimmed) in my case - blue is charging, red is end of charge (in my case - normally one expects red for charging...). I tested the panel with low light on a cloudy day (w/o heatsink) with a 100W 22V solar panel, I get about 20% more power compared with the MPPT of the XMUND XD-PS1 power station. I will test it also on a sunny day (with heatsink now) and I will add a comment.

MPPT 5A Güneş Paneli Regülatör Kontrol Cihazı Pil Şarjı 9V 12V 24V Otomatik Anahtar

US$13.99 US$16.99

6

Yorumlar (2)

Excellway 2200-7000 W Saf Sinüs Dalga İnvertör 220V 50HZ AB Standardı 12V/24V LED Ekran Güç İnvertörü

US$109.99 US$89.99

Q: Hi can what is the maximun power voltage of mensela 24volts 2200 watts. Can i run up to 28 volts or 29volts

Soran BG113255417 Açık 2022-09-05 10:18:55

Adi I verified (for Mensala 2200W) the input voltage up to 31 V and the over-voltage protection does not trigger; in an user manual (that comes with the inverter, for other inverter type anyway...) it is written 20 - 30 V battery voltage as limits of one class of inverters (I assume 24 V type; 10.5 - 15 V, I assume for 12 V type and 40 - 60 V, I assume for 48 V type).

2022-09-06 03:46:49 Yararlı

Gönder

cevaplar (1)

Adi 02/07/2022

Arrived fast from CZ, in 4 days, in good conditions. Tested with 100W solar panel - the power station uses 43 W maximum from panel (19.7 V, 2.2 A), the panel can provide 80 W (up to 4.5 A). The test indicates that it is not a problem to use a panel that can provide a higher current (with a voltage lower than 25 V - according to the user manual), the maximum charging power is close to the ac charger power, that is: 15V x 3A = 45W. It seems that the MPPT is active for the solar panel charge (e.g. with full sun: 19V x 2.2A, with some shadow: 14V 1.8A). The ac output can be activated when the power station is charged (from the solar panel or from ac charger - the charging input port is the same for both charging methods); the dc outputs (from the internal battery) are not active when charging, the USB ports are active also (indicated by the display, not tested). I used the ac output to charge a bike battery pack (36V, 10Ah) through its charger (42V, 2A), the dc charging current was 1.5A (not 2A, for 39V to 41V battery voltage) - image 1 and 2. The ac voltage was 227 Vrms (not verified the waveform - expected to be modified sine wave), I will verify later and if it is pure sine I would add a comment. I used also a LED lamp to verify the ac power output (image 3 and 4). Overall I consider this power station to be a good acquisition.

XMUND XD-PS1 222wh Taşınabilir Güç İstasyonu 3.7V 60000MAH Solar Jeneratör Acil Enerji Kaynağı Yedekleme Batarya Outdoor Kampçılık için Taşınabilir Güç Bankası

US$299.99 US$499.99

6

Yorumlar (1)

100W 18V Esnek Güneş Paneli Pil Güç Şarj Kiti RV Araba Boat Camping için

US$154.99 US$175.99

Q: What is the weight of a panel?

Soran BG216381736 Açık 2020-12-29 10:45:46

Adi 2.2 kg

2022-07-04 02:57:51 Yararlı

Gönder

cevaplar (1)

KROAK SP-01 20W 17.6V Shingled Güneş Paneli Esnek Açık Hava Su Geçirmez Taşınabilir Üstün Monokristalin Güneş Güç Hücresi Pil Şarj Cihazı Araba Kamp Telefon için

US$48.99 US$59.99

Q: Hello! Does 5v and 12v ports output simultaneously? Thanks!

Soran BG141521203 Açık 2022-07-02 10:56:48

Adi Yes they do work together but with a lower power. In my tests I get in direct evening sun (today, 19:00, a bit foggy) about 5 W maximum power at DC output (without USB, 16.3V x 0.3A). With both USB and DC connected I get: 0.2A x 4.2V = 0.85W at DC output plus 4.7V x 0.13A = 0.6W, total about 1.5W. With USB only I get 4.2V x 0.28A = 1.2W. With full sun I expect more power, I will add a review after the test.

2022-07-04 12:48:25 Yararlı (5)

Gönder

cevaplar (2)

Adi The voltage-current and power-current characteristics (5th image, 27 June 14:00 - full sun, with a max power: 13V x 0.5A = 6.5 W) were not published by the site :( .

Adi 02/07/2022

I received it after 5 days from CZ in good conditions. The system is functional with a maximum power of about 7 W (full sun, 17 June 14:00 1st image: Lead Acid Battery charge). At the panel dimension I expected less than 20 W anyway (0.1 sqM x 1000 W X 20% = 20 W). The open circuit voltage is 18.1 V (2nd image) and the short circuit current 0.54 A (3rd image), the temperature is about 50 degree C (4th image). The voltage-current and power-current characteristics were measured (with a constant current load - 5th image), the measurement at 0.5 A is visible in the 6th image. The controller current consumption (from battery or solar panel is of 12 mA). The controller disconnects the battery from panel at about 14.4V and reconnect it at about 13.5V, I did not notice the PWM operation. For small solar panels (like this one) it is a good choice, for higher solar power a MPPT controller would be more efficient. Overall I consider this a good deal (I bought it at about 30 USD); be aware that the solar panel power is less than 10 W.

100W Güneş Paneli seti 12V pil Şarj Cihazı 10-100A LCD Kontrolör Karavan Van Tekne için

US$30.74 US$39.99

56

Yorumlar (13)

100W Güneş Paneli seti 12V pil Şarj Cihazı 10-100A LCD Kontrolör Karavan Van Tekne için

US$30.74 US$39.99

Q: 100 watts?

Soran BG511365540 Açık 2022-05-06 08:23:21

Adi I measured the solar panel with a constant current load with full sun on June 27, 14:00 and I get a maximum power of 6.5 W (13V x 0.52A = 6.5W). Charging the lead-acid battery I get a maximum of 7.3 W (0.52A x 14V = 7.3W). I expected a power less than 20 W anyway (0.1 sqm x 1000 W x 20% = 20 W).

2022-07-04 02:09:31 Yararlı (6)

Gönder

cevaplar (3)

Adi 02/07/2022

Fast delivery, in just 5 days; the package was broken (2nd image), but no damage to the item. easy to install. It does not start, the problem was the safety lock, it should be connected to the phone pad (magnetically, 3rd image). My wife is very happy after testing and using the treadmill. It is a good deal, especially when the special offer is valid (I bough it to about 200 USD).

[EU Direct] XMUND XD-T2 Taşınabilir Koşu Bandı 12km/s Koşu Modu Ayarlanabilir LCD Ekran Smart WalkingPad Gym Ana Sayfa Fitnes Ekipman

US$459.99

0

Yorumlar (0)

Adi 19/12/2018

I received the 3 products, one of them does not operate (frontal light). I disasambled it and solder one wire; now it's operating... I will check the battery capacity and I will add a new comment. The light is quite bright, the charging time is less than one hour (1st charge, maybe partially charged), the switch is a bit difficult to operate, the light zoom is easy to use and the price was good (5 USD each). Overall I consider this a good product.

XANES 1517B XPE + COB Çift Işıklı 1000Lümen Zoomlu USB Şarj Edilebilir EDC Taktik LED El Feneri Takımı

US$10.99 US$13.99

7

Yorumlar (2)

JINHAN SMTO502S 60MHz 250MSa / s Örnekleme Hızı Dokunmatik Ekran Osiloskop USB Osiloskops 2 Kanal + Sinyal Üreteci

US$165.89 US$189.99

Q: Is it possible to save the image and/or waveform to an external device (e.g. USB stick or USB to computer)?

Soran Adi Açık 2021-05-31 12:35:11

Crowbar8 it can

2021-06-02 05:08:07 Yararlı (1)

Gönder

cevaplar (1)

Adi@BG573744020 The watch stops yesterday... it can be charged but no other operation is valid - seems that the screen cover is broken - poor material - last for 1 year and 2 month... I changed the bracelet 2 month ago (the original ones get broken - the material is sable for about one year...)

Adi 30/10/2018

I used it for 2weeks, first recharge last for about 6days (with highest brightness, recharged at 20% remaining battery), the second recharge: after 7 days is at 66% (with normal brightness). The application can be improved: to memorize the actual measurement (not only the score); to set the brightness from application (for day / night); to set recurrent measurement... The BT communication for blood measurements often fails. The brightness has 3 basic levels: 1 - very low - can be used during the night (1 line), the second is for normal indoor use (2-3 lines) and the third one is for outdoor used (3 levels almost identical: 4-6 lines, vizible in sunny days). The watch need a smart phone connection to set up the time (at least first time). If BT fails, it should be restarted the BT from the phone (smart watch reset does not help, only resets all your measurements...). In the manual it is indicated not to swim, in the advertising swiming is allowed - I did not swim with the watch (swiming was one of the reason I select this watch...) Overall I consider it a very good aquisition for the price I paid.