I well-know this product and it’s my favorite servo since 2 Years: the 4409MG comes in a little, a bit anonimous box, but it’s like to open a treasure chest: in a little piece of carton, the metallic-red of the main body of the servo stings your eyes with its brilliance; removing the folded paper support, You can discover a complete collection of arms and mounting accessories that can be used not just for RC cars, but for robotics and other actuation purposes. The servo has a long, good quality silicon cable with standard JST connector, four mounting open holes on the sides and is build of good plastic material and a (probably) metallic main section. The metallic main gear shaft provides a hole for M3 standard screws and 25-tooths (Futaba standard) profile. About performances, I initially bought it just for the price, so I was wondered when starting to use it: even if someone can think 0.13-0.11s/60deg is not so fast, I realized this can be enough even in very small corner radius tracks. In fact, after an initially negative impression, I just added a very little more roll to my car, tryied different toe angles and... BAM! It started flip-flopping at lightspeed! But that’s not all, folks! The faster You run, the biggest are the damages in case of crash... this 4409MG have a very powerful torque value, that helps both to steer and resisting to hi-speed wheel impacts: in our RC club we run indoor and use foam, high-grip tyres and the track width sometimes is small, so wheel-to-wheel side contacts often occours; in this situation, normal servos may break, but the 4409MG have good chances to resist. Finally, a note about dimensions: despite this is a standard 1/10th scale servo, it has a low-profile design, which truly is a bonus if You need to use it in a modern, narrowed design RC car chassis...

I well-know this product and it’s my favorite servo since 2 Years: the 4409MG comes in a little, a bit anonimous box, but it’s like to open a treasure chest: in a little piece of carton, the metallic-red of the main body of the servo stings your eyes with its brilliance; removing the folded paper support, You can discover a complete collection of arms and mounting accessories that can be used not just for RC cars, but for robotics and other actuation purposes. The servo has a long, good quality silicon cable with standard JST connector, four mounting open holes on the sides and is build of good plastic material and a (probably) metallic main section. The metallic main gear shaft provides a hole for M3 standard screws and 25-tooths (Futaba standard) profile. About performances, I initially bought it just for the price, so I was wondered when starting to use it: even if someone can think 0.13-0.11s/60deg is not so fast, I realized this can be enough even in very small corner radius tracks. In fact, after an initially negative impression, I just added a very little more roll to my car, tryied different toe angles and... BAM! It started flip-flopping at lightspeed! But that’s not all, folks! The faster You run, the biggest are the damages in case of crash... this 4409MG have a very powerful torque value, that helps both to steer and resisting to hi-speed wheel impacts: in our RC club we run indoor and use foam, high-grip tyres and the track width sometimes is small, so wheel-to-wheel side contacts often occours; in this situation, normal servos may break, but the 4409MG have good chances to resist. Finally, a note about dimensions: despite this is a standard 1/10th scale servo, it has a low-profile design, which truly is a bonus if You need to use it in a modern, narrowed design RC car chassis...

I well-know this product and it’s my favorite servo since 2 Years: the 4409MG comes in a little, a bit anonimous box, but it’s like to open a treasure chest: in a little piece of carton, the metallic-red of the main body of the servo stings your eyes with its brilliance; removing the folded paper support, You can discover a complete collection of arms and mounting accessories that can be used not just for RC cars, but for robotics and other actuation purposes. The servo has a long, good quality silicon cable with standard JST connector, four mounting open holes on the sides and is build of good plastic material and a (probably) metallic main section. The metallic main gear shaft provides a hole for M3 standard screws and 25-tooths (Futaba standard) profile. About performances, I initially bought it just for the price, so I was wondered when starting to use it: even if someone can think 0.13-0.11s/60deg is not so fast, I realized this can be enough even in very small corner radius tracks. In fact, after an initially negative impression, I just added a very little more roll to my car, tryied different toe angles and... BAM! It started flip-flopping at lightspeed! But that’s not all, folks! The faster You run, the biggest are the damages in case of crash... this 4409MG have a very powerful torque value, that helps both to steer and resisting to hi-speed wheel impacts: in our RC club we run indoor and use foam, high-grip tyres and the track width sometimes is small, so wheel-to-wheel side contacts often occours; in this situation, normal servos may break, but the 4409MG have good chances to resist. Finally, a note about dimensions: despite this is a standard 1/10th scale servo, it has a low-profile design, which truly is a bonus if You need to use it in a modern, narrowed design RC car chassis...

Comes as described. Fast process and delivery. Hope it perform and last as my other JX servos. Thanks.

Comes as described. Fast process and delivery. Hope it perform and last as my other JX servos. Thanks.

Comes as described. Fast process and delivery. Hope it perform and last as my other JX servos. Thanks.