just unpack, already tested. good product. not the best one, but it's a good 3d printer.

just unpack, already tested. good product. not the best one, but it's a good 3d printer.

just unpack, already tested. good product. not the best one, but it's a good 3d printer.

good

good

good

Delivery is very fast. The product is not yet assembled, but I expect it will work well after being assembled well. I am a little disappointed that the assembly instructions are not included. So, I hope to be enclosed with the follow-up products.

Delivery is very fast. The product is not yet assembled, but I expect it will work well after being assembled well. I am a little disappointed that the assembly instructions are not included. So, I hope to be enclosed with the follow-up products.

Delivery is very fast. The product is not yet assembled, but I expect it will work well after being assembled well. I am a little disappointed that the assembly instructions are not included. So, I hope to be enclosed with the follow-up products.

Absolutely no customer support, manual on Memory chip is scattered and chip is damaged in transit. Can use most of the data not written in English. Only way to use it is to stumble along with partial data and trial and error.

Absolutely no customer support, manual on Memory chip is scattered and chip is damaged in transit. Can use most of the data not written in English. Only way to use it is to stumble along with partial data and trial and error.

Absolutely no customer support, manual on Memory chip is scattered and chip is damaged in transit. Can use most of the data not written in English. Only way to use it is to stumble along with partial data and trial and error.

This machine is a hot mess, do not buy it as it does not work at all, it does not deserve 1 star Main issues; - You can't put the LCD screen on or the hot end will hit it - The Z & Y axis motors & extruders are not strong enough and skip lots of steps (Z axis sometimes stalls and does not move). - Heated bed is bowed badly which means you can't print over the entire bed. - Heated bed cords line up perfectly with the Y axis motor which means it hits the motors and jams every time you print on front third of the bed - Only one of the X axis wheels have a cam nut leaving the side counterbalanced loose and able to move up and down when printing. - The Extruders have burs and sharp edges which strip the side off the filament as it is fed through - The Extruders often stop due to being direct drive and motors not powerful enough. - The belts on the carriages are too loose and don't have any way of tightening them which causes major accuracy and surface issues - No cable management - Bottom of 240V power supply is open and unsafe - Power Supply fan is super noisy, you can't here the rest of the machine over this - Heated Bed Sticker does not release prints making it a pita to get prints off when done - Idler wheel on the X axis is too large and causes the belt to rub constantly against the wheels on the X carriage - Idler wheel on Y axis is too small, allow the belt to rub on the rail and changes the length of the belt as it gets closer to the front of bed - The poor connection of Y axis to main frame leaves the whole frame wobbly and it moves around a little when printing - No auto level sensor - Heated bed sticker came complete scratched up as it is against bottom of shipping box

This machine is a hot mess, do not buy it as it does not work at all, it does not deserve 1 star Main issues; - You can't put the LCD screen on or the hot end will hit it - The Z & Y axis motors & extruders are not strong enough and skip lots of steps (Z axis sometimes stalls and does not move). - Heated bed is bowed badly which means you can't print over the entire bed. - Heated bed cords line up perfectly with the Y axis motor which means it hits the motors and jams every time you print on front third of the bed - Only one of the X axis wheels have a cam nut leaving the side counterbalanced loose and able to move up and down when printing. - The Extruders have burs and sharp edges which strip the side off the filament as it is fed through - The Extruders often stop due to being direct drive and motors not powerful enough. - The belts on the carriages are too loose and don't have any way of tightening them which causes major accuracy and surface issues - No cable management - Bottom of 240V power supply is open and unsafe - Power Supply fan is super noisy, you can't here the rest of the machine over this - Heated Bed Sticker does not release prints making it a pita to get prints off when done - Idler wheel on the X axis is too large and causes the belt to rub constantly against the wheels on the X carriage - Idler wheel on Y axis is too small, allow the belt to rub on the rail and changes the length of the belt as it gets closer to the front of bed - The poor connection of Y axis to main frame leaves the whole frame wobbly and it moves around a little when printing - No auto level sensor - Heated bed sticker came complete scratched up as it is against bottom of shipping box

This machine is a hot mess, do not buy it as it does not work at all, it does not deserve 1 star Main issues; - You can't put the LCD screen on or the hot end will hit it - The Z & Y axis motors & extruders are not strong enough and skip lots of steps (Z axis sometimes stalls and does not move). - Heated bed is bowed badly which means you can't print over the entire bed. - Heated bed cords line up perfectly with the Y axis motor which means it hits the motors and jams every time you print on front third of the bed - Only one of the X axis wheels have a cam nut leaving the side counterbalanced loose and able to move up and down when printing. - The Extruders have burs and sharp edges which strip the side off the filament as it is fed through - The Extruders often stop due to being direct drive and motors not powerful enough. - The belts on the carriages are too loose and don't have any way of tightening them which causes major accuracy and surface issues - No cable management - Bottom of 240V power supply is open and unsafe - Power Supply fan is super noisy, you can't here the rest of the machine over this - Heated Bed Sticker does not release prints making it a pita to get prints off when done - Idler wheel on the X axis is too large and causes the belt to rub constantly against the wheels on the X carriage - Idler wheel on Y axis is too small, allow the belt to rub on the rail and changes the length of the belt as it gets closer to the front of bed - The poor connection of Y axis to main frame leaves the whole frame wobbly and it moves around a little when printing - No auto level sensor - Heated bed sticker came complete scratched up as it is against bottom of shipping box