Tüm Mesajlar

Q: Do you have it in 110V ?

Soran Roberto Garcia Açık 2018-09-21 07:27:41

fernandojoaquim3 Thismodel is 220v AC and will not function on 110v AC.

2022-09-30 05:20:39 Yararlı (0)
Gönder
cevaplar (2)

Q: Is saw blade included?

Soran Ivicae54 Açık 2022-01-27 10:22:31

fernandojoaquim3 No,ablade is not included,and is to be purchased separately .Please note spindle size.

2022-09-30 05:17:15 Yararlı (0)
Gönder
cevaplar (2)

fernandojoaquim3 The chuck body on these chucks is not threaded,hence the chuck can be mounted on your MC900 via an adapter plate,bought or fabricated.

2022-05-21 05:37:00 Yararlı (0)
Gönder
cevaplar (2)

fernandojoaquim3 Yes,aninternal threading bar is included in the set.

2022-05-21 05:33:42 Yararlı (0)
Gönder
cevaplar (1)

fernandojoaquim3 SanOu manufactures chucks in various configurations,these designated by model number.Each model is designed to hold work pieces according to function.K72= 4 jaw INDEPENDENT chuck means you adjust each individual jaw one at a time,therefor used to clamp square or rectangular work pieces at offset (or centralized)positions as well as round stock which the operator will center using a dial gauge.San Ou K-02,K-12 are 4 jaw self-centering chucks.

2022-03-29 05:25:33 Yararlı (0)
Gönder
cevaplar (2)

fernandojoaquim3 Unset di inserti (uno per utensile) viene fornito con il set, tuttavia gli inserti separati dovranno essere acquistati separatamente

2021-12-17 12:42:46 Yararlı (0)
Gönder
cevaplar (5)

Q: Can I buy insert retaining screws for these tools?

Soran Bluey66 Açık 2021-04-19 03:51:27

fernandojoaquim3 Yes,separatereplacement screws are available.Should you have stripped the tool insert threads,simply tap to the next available size thread with an adequately sized tap and obtain matching sized screws.

2021-12-17 12:39:37 Yararlı (0)
Gönder
cevaplar (2)

fernandojoaquim3 TheK72-80 has 3 (three) equal-spaced M6 threaded mounting holes on the rear of the chuck( the unit I received has 3 holes).

2021-12-14 05:01:07 Yararlı (0)
Gönder
cevaplar (3)

Q: What is the size of the motor shaft?

Soran vellarod Açık 2019-04-19 03:44:32

fernandojoaquim3 Motorshaft size on the working(or pinion) end is: length =11,5mm ,, diameter 3.18mm (note that the shaft is beveled,d-shaped),and total motor shaft length = 68.8mm (back to front)

2021-11-19 07:57:24 Yararlı (0)
Gönder
cevaplar (2)

fernandojoaquim3 Thereare many enclosures or casings in which one can mount these units.I recommend using an old or existing halogen floodlight casing(normally a cast aluminium shell with a glass door and seal) ,remove the existing halogen lamp holder etc,and convert it to the led unit.Have done so,the led unit has worked in the casing for close on 2 years....no water ingress problems.

2021-07-13 08:37:38 Yararlı (0)
Gönder
cevaplar (2)

Q: Is this a 3 or 5mm shaft for the pinion gear????

Soran CantennaB Açık 2021-04-27 05:30:52

fernandojoaquim3 Standard3.2 mm motor shaft with flat machined edge ("D" shaped viewed from the front).

2021-07-13 07:39:38 Yararlı (1)
Gönder
cevaplar (4)

Q: Can this chuck be used for cutting steel?

Soran mrbishop Açık 2019-11-02 12:40:09

fernandojoaquim3 Yes,however,notrecommended for clamping steel work-pieces.Likely slippage of a ferrous steel piece in the chuck may result in shearing damage to the chuck jaws. Do so at your own discretion.

2021-07-13 07:39:08 Yararlı (0)
Gönder
cevaplar (3)