Tüm Mesajlar

Q: Where are the building instructions? (PDF download?)

Soran elmar2b Açık 2023-08-28 06:05:20

Bizzmo_ Hi, thers is no building instructions for this item.

2023-09-02 01:54:20 Yararlı (0)
Gönder
cevaplar (1)

Q: how many grams of trust does this set generate?

Soran elmar2b Açık 2019-05-29 01:11:46

deel Yes This is what I used

2022-02-08 09:53:15 Yararlı (0)
Gönder
cevaplar (1)

BG481912204 somethingbetween 0 and ~

2021-10-03 05:38:03 Yararlı (0)
Gönder
cevaplar (1)

Q: Jst SH 1.0mm pitch?

Soran elmar2b Açık 2020-05-11 05:56:37

Starmanut Theseare no longer available.

2021-09-30 08:49:49 Yararlı (0)
Gönder
cevaplar (2)

Q: Which protocol is the receiver?

Soran elmar2b Açık 2021-04-25 03:04:08

Chartreuse volantex's own protocol.

2021-05-10 04:45:37 Yararlı (1)
Gönder
cevaplar (1)

Q: What is the connector type? Jst sh 1.00mm?

Soran elmar2b Açık 2021-03-10 11:17:21

Sempiternal Hello, we have sent your question to the supplier, will get back to you soon.

2021-04-08 06:05:17 Yararlı (0)
Gönder
cevaplar (1)

zolatanaffa considering the big component (marked LM2 ... on the back of the printed board) which should be a switch to power and regulate the motor and the two-pole connector (called MO on the pcb, next to the two servos on the side of the receiver circuit added to the main board) it seems so. I had an A800 but I missed it in flight before checking the electronic circuitry on board, so I'm not 100% sure. I must say though that if you look at the fuselage from the outside and calculate that: starting from the bow towards the wings: all the space before the black cowling is occupied by the engine, all the space hidden by the black cowling is dedicated to the battery, the electronic card is positioned near the wing's leading edge, so there is almost certainly no room for an additional esc. P.S. the motor is brushed so the esc is not a three wire output, here is another reason why it is probably enough to connect the motor to the receiver

2019-06-23 01:32:47 Yararlı (4)
Gönder
cevaplar (2)

Q: what is the size of bullet plugs? 2mm?

Soran elmar2b Açık 2019-07-08 02:16:38

Gruey27 2mm

2021-02-06 06:22:09 Yararlı (1)
Gönder
cevaplar (2)

Q: what is the weight of this receiver?

Soran elmartobi Açık 2019-05-23 03:27:14

Luis Cepeda About 7 grams

2020-10-01 01:49:48 Yararlı (1)
Gönder
cevaplar (1)

Q: Can you upgrade a G-RX8 with this tool?

Soran elmar2b Açık 2020-08-11 03:21:04

Gavin yes

2020-08-25 03:46:10 Yararlı (1)
Gönder
cevaplar (1)

Q: Are the servo sockets jst-sh 1.00mm?

Soran elmar2b Açık 2020-07-30 01:00:05

dengjunbao Plug Size: 1.00Pin 3P

2020-08-03 08:37:10 Yararlı (1)
Gönder
cevaplar (1)

iedutz no.it'a 3.7v. it will burn out

2020-08-03 03:38:44 Yararlı (1)
Gönder
cevaplar (1)

Q: 5.5", but what is the pitch?

Soran elmar2b Açık 2020-05-31 03:30:37

Bridoon not sure

2020-06-07 08:54:43 Yararlı (0)
Gönder
cevaplar (1)

Q: What is the size of the bullet connectors?

Soran elmar2b Açık 2020-05-02 05:47:37

Cardboar 3.5mm banana female connector

2020-06-01 10:28:54 Yararlı (1)
Gönder
cevaplar (1)

Q: what is the connector? 1.25 mm or 1mm?

Soran elmartobi Açık 2019-05-23 05:33:08

Mark 2mmas far as i remember, but i would check before ordering

2020-05-25 01:57:18 Yararlı (0)
Gönder
cevaplar (1)

Q: what is the weight of this lipo?

Soran elmartobi Açık 2019-05-23 05:32:22

Mark Theyare light, but i dont have scales that can weigh these

2020-05-25 01:56:10 Yararlı (0)
Gönder
cevaplar (1)