mischu.buero_hh
İçeriklerim
Tüm Mesajlar
İncelemeler
Yorumlar
cevaplar
Sorular

Tüm Mesajlar

mischu.buero_hh 04/01/2020
NiZn werden NICHT automatisch erkannt, sondern müssen manuell eingestellt werden. Sonst Top Ladegerät. Passendes Netzteil gleich mitordern.
LiIon LiHv LiFe NiMh Nicd Nizn için LCD AA/AAA Pil Hızlı Şarj Aleti ISDT N8 18W 1.5A 8 Yuvalı
US$73.79 US$63.59
0
Tavsiyeler
Yorumlar (1)
mischu.buero_hh 06/06/2020
Einfacher Start - mit den richtigen Bibliotheken und Codezeilen! Das Display ist super, aber viele haben Probleme, es in Betrieb zu nehmen: "Das Display bleibt weiß" oder "nur die Hintergrundbeleutung geht an" sind häufige Klagen von Käufern. So habe ich das Problem mit dem "white screen" lösen können: 1) DIESE Library herunterladen: http://www.rinkydinkelectronics.com/library.php?id=51. Aktuell ist die Version 2.83. 2) Arduino IDE öffnen. In der Menüleiste auf SKETCH / BIBLIOTHEK EINBINDEN / ZIP-BIBLIOTHEK HINZUFÜGEN klicken und im Dateisuch-Fenster die UTF-Zip-Datei suchen und auswählen. In der Statuszeile sollte die Meldung erscheinen, dass die Bibliothelk hinzugefügt wurde. 3) Besser ist das: Arduino Mega anschließen und erstmal testen, sofern es auch neu ist. Selbstverständlich sicherstellen, dass unter WERKZEUGE das richtige Board und der richtige Port eingestellt ist. Eines meiner Boards von banggood war nämlich defekt (Lötbrücke), da kann man lange nach Codefehlern suchen. Läuft alles? Dann abstecken. 4) Das Display mit dem Shield aufsetzen. 5) In der IDE auf DATEI / BEISPIELE / UTFT / Arduino (ARM) + Teensy / UTFT_Demo_320x240 gehen 6) In Zeile 27 den Code ändern in: UTFT myGLCD(ILI9341_16,38,39,40,41); // TFT ILI9341_16b 7) Arduino anstecken. Sketch hochladen 8) Freuen. :-)
Arduino ile uyumlu olarak çalışan 3.2 İnç ILI9341 TFT LCD Ekran Modülü Dokunmatik Panel Geekcreit - resmi Arduino panolarıyla çalışan ürünler
US$22.99 US$32.99
1
Tavsiyeler
Yorumlar (0)
3.3V TFT LCD Ayarlanabilir Kalkan Genişleme Kartı Mega 2560 R3 3.2
US$12.99 US$15.99

Q: Touch screen does not work. I'm having 3 of this shields, and same problem with each shield. Any other shield from adafruit etc. works fine by using the libraries UTFT and UTouch from Henning Karlssen (***** with standard setup [UTouch myTouch(6,5,4,3,2);] for MEGA 2560. I tried several other PIN-Setups, but nothing worked. So i measured a working shield comparing to THIS shields - and found out that THIS shields don't lead the touch signals to the Touch-PINs of the MEGA-Board. But any other shield does. So i looked once again if another PIN-Setup will work, but this failed. On mikrocontroller.net i found a thread abaout THIS shields and read, that the shield has 2 mistakes in board layout which causes the dead touch. In this thread, they re-soldered 2 PINs an connected them manually to the mega-board. Isn't there another solution?

Soran mischu.buero_hh Açık 2020-06-21 02:25:31

dalibaba I hope the manual can help you. http://myosuploads3.banggood.com/products/20200619/202006192159153.2.zip

2020-06-22 02:26:07 Yararlı (0)
Gönder
cevaplar (1)

Uzmansın, yardım edebilir misin?

Sizi Davet Yanıtı e-postasına abone olmaya içtenlikle davet ediyoruz!

Abone olursanız, sizi e-posta yoluyla insanların ürünlerle ilgili sorularını yanıtlamaya davet edeceğiz. Size abone olarak] ayrıca "Yararlı Rozeti " kazanacaksınız! Gizlilik ayarları sayfasından istediğiniz zaman aboneliğinizi iptal edebilirsiniz.

Başkalarına yardım edin ve daha mutlu olun!

  • Abone ol

Rozetler Hakkında

Rozetler toplulukla ilgilidir ve kullanıcılar kaliteli içerik oluşturarak, görevleri tamamlayarak veya özel etkinliklere katılarak rozet kazanırlar. Belirli kişilerin kendi özel rozetlerine sahip olmaları gerekir.
CEO ROZETİ

The CEO ünvanı yalnızca Banggood patronuna aittir.

Kazanabileceğiniz rozetler yakında geliyor
  • TAMAM

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • TAMAM

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe