Tüm Mesajlar

Franklydude Strange why there are "experts" talking about torque and rotor precession. It's only because of tail rotor sideways force, helicopter tilts to compensate.

2023-03-03 03:40:54 Yararlı (2)
Gönder
cevaplar (15)

Franklydude Iwould guess the front panel comes off, exposing the mounting plate, then you have to figure out how to use two screws to fix to the wall or the plastic mounting box set into the wall, which is tricky as most boxes I have seen doen't have a obvious screw hole, or if they do, it's very flimsy. I have used epoxy resin type products to build up material on the left and right of the plastic box set in the wall, but t's a hassle. A better option I think is to cut out the round plastic "EU" style wall box and use a UK style square box. they are usually metal, unless designed for use with drywall, plaster board. They come in at least 3 different depths, but for a smart switch etc you need a deep one

husmen73 28/08/2020
0
Yorumlar (1)

JSCC Look at the photo of the underside, it has two water screws.

2020-11-20 07:57:19 Yararlı (0)
Gönder
cevaplar (1)

Q: Can we make an aroplane with this engine

Soran rikularwann567 Açık 2019-11-27 09:56:37

Franklydude Why not? the title says car bot plane

2020-11-02 06:58:43 Yararlı (0)
Gönder
cevaplar (2)

Q: Is there a video of this model in flight?

Soran twointhebush0111 Açık 2020-08-14 10:44:04

Franklydude most likely not! It would not have a hope in hell of flying and that tiny direct drive motor would not have enough thrust to achieve lift off from water....so I'd be very interested in a maiden flight too!

2020-08-19 02:19:41 Yararlı (1)
Gönder
cevaplar (1)

xoverstudio because it is miniaturized. the dimensions are noticeably different.Size: 18 × 10 × 2.6mm against the Size: 20mm*11mm*5mm (L *W*H) the weight is 0.8 grams, against the 6.2 grams of the other. its weight and dimensions make it perfect for use on drones, planes etc.

2020-04-22 04:53:25 Yararlı (3)
Gönder
cevaplar (1)

Q: which geared motor do I need, is it A B or C from you list Thank you

Soran robertrollins Açık 2019-10-27 09:55:30

Franklydude C motor is 7mm x 16mm, while B is 7mm by 20mm and A is a 8 x 20mm motor I would suggest the C or B are suitable

2019-11-04 05:14:47 Yararlı (1)
Gönder
cevaplar (1)

Franklydude Thereceiver shown on the photos of the assembled unit does have a 2A Brushed ESC built into the receiver board. The receiver is listed on Banggood web site:- 2_4G-4CH-Micro-Low-Voltage-DSM2-DSMX-Compatible-Receiver-Built-in-Brushed-ESC

Gumbo 11/05/2019
8
Yorumlar (5)

Franklydude to Van Gogh,, if it is "easy" as you say, please could you post where the electrolytics go, and what the switches do and how to calibrate it? PLEASE?

2019-04-20 01:23:53 Yararlı (0)
Gönder
cevaplar (3)

Franklydude Could some one please post the capacitor values... please...

2019-04-16 06:58:04 Yararlı (0)
Gönder
cevaplar (3)