Tüm Mesajlar

Imbueeeam Press and hold the learning button for three seconds, the indicator light will go off, and then press any button on the remote control. The indicator light flashes four times and then stays on, which means the learning is successful.

2020-10-07 09:52:37 Yararlı (0)
Gönder
cevaplar (1)

Q: how many controls support?

Soran Karla Açık 2019-02-06 12:39:43

eeenok obviously it supports at least two controllers, since that's a purchase option. it probably supports more, since the one circuit will be used in different products. i'd be surprised if both controllers need to be the same code, so switch can probably remember about eight. and since switch supports "latch" mode, you can probably use one controller as on and another as off. exact answer is hard to find the cheapest way to buy controllers is with the initial purchase, so try to find one with the number of transmitters you want

2020-09-25 09:00:17 Yararlı (0)
Gönder
cevaplar (2)

eeenok you want jog ("inch mode"), not toggle. the instructions say this is 1+2, but the circuit board says it is no jumper. you'll need to experiment

2020-09-23 01:44:56 Yararlı (0)
Gönder
cevaplar (2)

eeenok (1) try re-binding remote (2) check your 12v supply to receiver isn't noisy. power going to load can be noisy

2020-09-23 01:37:18 Yararlı (0)
Gönder
cevaplar (8)

eeenok i don't think it can "change state" on power-up (NC starts connected, NO starts disconnected) but your equipment will start on if you connect to NC+COM and use OFF to turn ON. equipment will be on if right side has power, even if receiver has no power. if your equipment is 12V, then power receiver AND NC+COM with same supply and equipment will work when providing 12V

2020-09-23 01:14:45 Yararlı (0)
Gönder
cevaplar (4)

eeenok assume 4000W is peak output, not continuous rating. 10000W controllers are not much more expensive. these voltage controllers don't work on INDUCTION MOTORS (i think) so a large motor should be tested

2020-06-05 07:57:58 Yararlı (0)
Gönder
cevaplar (2)

Q: Hi will this work to regulate the heat of a 3000W geyser element

Soran BG214865537 Açık 2020-06-01 01:59:45

eeenok unless you can find the exact specs, assume 4000W is peak rating and continuous power is only 2000W. this is the case for a similar 4000W SCR controller i found the details for. you are looking for whether that maximum current of 18 or 20 amps is continuous (4000W = 18A continuous current) or peak (2000W = 9A continuous current). if the continuous rating is only 2kW, it's not enough for your geyser

2020-06-04 11:29:32 Yararlı (0)
Gönder
cevaplar (2)

eeenok all "4000W" controllers use the same circuit. assume 2000W! test whether earth is connected! test whether circuit can move inside case! doesn't work on induction motors. large motors might be induction. don't pay attention to americans. they take no pride in their spelling.

2020-06-04 12:33:37 Yararlı (0)
Gönder
cevaplar (2)

Q: What is The constant power output? 4000w is max

Soran ezutel Açık 2019-11-17 08:36:17

eeenok it's just amazing to think that someone who doesn't understand the difference between voltage and power has the confidence to answer electrical questions on the internet! wtf tamem888 the rated power of this is about 2000W, based on another site listing peak current at 18A and rated current 9A. it will be a bit less if they're talking input rather than output power, but these switching devices are pretty efficient so there's not a big difference

2020-06-03 11:55:27 Yararlı (0)
Gönder
cevaplar (2)

eeenok the much larger number is what you need to pay to get the slide hammer. the ad is deliberately misleading

2020-05-11 03:45:04 Yararlı (0)
Gönder
cevaplar (2)

eeenok it's a very loud beep. sirens are different tech, with rotating holes chopping air pressure on & off. the wailing is because of spin-up & spin-down time of the rotating element

2020-03-29 12:25:15 Yararlı (0)
Gönder
cevaplar (5)

Q: UNİVERSAL?

Soran drone_manyaq Açık 2019-11-05 01:26:32

eeenok universally stupid. you cannot replace CO2 by pumping in more air

2020-02-06 05:33:10 Yararlı (0)
Gönder
cevaplar (3)

Q: is it genuine japan movement, not some chinese fake?

Soran mirek Açık 2018-04-18 01:03:03

eeenok it's not as simple as chinese = fake. seiko has factories in china. it might be seiko, seiko factory second, good chinese clone or bad clone. research is needed

2019-10-03 09:08:14 Yararlı (1)
Gönder
cevaplar (2)

eeenok it will work without a ground/earth but you should earth the heatsink in case a fault makes it live. do not call your earth "neutral". don't connect heatsink to N! treat L and N as equally dangerous since they are sometimes swapped. if you don't earth HS, treat the device as LIVE when on

2019-09-19 10:29:36 Yararlı (0)
Gönder
cevaplar (3)

eeenok your DVR will have a (RCA) video out connector (unless it only has HDMI connections ... rare). this should work fine. looks like audio is only mono so you either pick one channel or you work out whether your DVR can output mono on one connector. the D in DVR is for digital, but that is just the digital recording system. HDMI ouputs are digital, but RCA connectors for video (usually yellow) and audio (red & white) are strictly analog (except electrical S/PDIF audio outputs ... now rare). you will need a cable that converts the transmitter input from FPC-style plug to RCA, but the receiver will plug straight into a tv if it has RCA video & audio inputs. on the receiver, you can use a 1-to-2 adapter to connect the mono to stereo inputs (but many devices let you set one connector as the mono input for both channels). theoretically you're not supposed to use that adapter on the transmitter end to mix a stereo into one mono output, but it's usually fine on high impedance outputs

2018-11-04 05:41:21 Yararlı (0)
Gönder
cevaplar (6)