ericdrob67
Q: What is recommended C rate for charging?
Soran ericdrob67 Açık 2018-09-02 08:37:23
Lynn 80C
2018-09-03 01:40:30 Yararlı (0)
Lanny Hello, thanks for your recommendation.
2018-10-07 08:12:53 Yararlı (0)Q: what type the propeler shoud be CCW or CW?
Soran Vasil Doctorov Açık 2018-02-27 04:08:14
ericdrob67 Its not discernible if there is any built in thrust angle on the firewall. I appears to be neutral, but i cant confirm. Planes generally run CCW props, but in a true neutral set up either should work fine.
2018-09-01 09:07:22 Yararlı (0)Q: can the receiver be swapped out for frsky receiver or bind with a taranis
Soran Jacko86 Açık 2018-08-12 03:12:35
ericdrob67 if you have a Taranis, then get a flysky module and it will work. I would recommend the IrangeX multi protocol module... for $38 it will allow you to use Taranis with almost everything
2018-08-23 11:46:35 Yararlı (0)Q: can the receiver be swapped out for a frsky receiver
Soran Jacko86 Açık 2018-08-12 03:09:28
ericdrob67 yes
2018-08-22 12:40:18 Yararlı (0)Q: Does an aileron of this fuselage move?
Soran t.tani0828 Açık 2018-04-05 10:44:01
ericdrob67 this is a 4 channel plane, so yes the Ailerons move, however they are not connected to the fuselage, they are connected to the wings..... perhaps this is a translation issue.
2018-07-21 03:18:38 Yararlı (0)
Q: has anyone tried to "reverse" the shaft on these so it comes out the mounting side?
Soran ericdrob67 Açık 2018-05-15 11:47:32
Eddy Hsia dude, c clip on bottom. try it and let us know.
2018-06-15 08:11:54 Yararlı (0)Q: What is the weight of this? per piece or how many pieces per gram
Soran ericdrob67 Açık 2018-05-11 03:39:04Q: What is the weight of this?
Soran ericdrob67 Açık 2018-05-10 06:28:16
Satnav8 The product weight is about 30g.
2018-05-16 03:58:38 Yararlı (0)Sizi Davet Yanıtı e-postasına abone olmaya içtenlikle davet ediyoruz!
Abone olursanız, sizi e-posta yoluyla insanların ürünlerle ilgili sorularını yanıtlamaya davet edeceğiz. Size abone olarak] ayrıca "Yararlı Rozeti " kazanacaksınız! Gizlilik ayarları sayfasından istediğiniz zaman aboneliğinizi iptal edebilirsiniz.
Başkalarına yardım edin ve daha mutlu olun!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ericdrob67 You need a different prop for press fit on a 1.5mm shaft. These props are for 11xx motors that are threaded to screw the prop on.